User manual KENWOOD TH-G71A

[. . . ] 1 Activating the Tone Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Selecting a Tone Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Automatic Repeater Offset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 TRANSMITTING A 1750 Hz TONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] <Log meter> · When the Internal GPS receiver is ON, the " indicator appears on the display. " <GPS satellite information> Sky view · When the Internal GPS receiver is On, the internal Satellite signal-strength bars clock is automatically configured with the time data from the internal GPS receiver. · You must set the time zone beforehand, through Menu No. 196. · When determining your position for the first time The sky view shows the satellites you are receiving. The satellite signal-strength bars indicate the strength of each satellite you are receiving. A solid bar indicates that the GPS satellite is ready for use. · When only the frame of the signal-strength bar is displayed, the satellite has not yet been captured. Note: When GPS cannot be received, turn the power ON in a clear environment (Open Sky). While the above screen is displayed (the GPS satellite information screen is positioning) press [MARK] (1s) to register a Mark Waypoint. While the above screen is displayed, pressing [PTT] will change to the frequency display and transmission will begin. Once transmission is complete, the transceiver returns to the original display. You may experience interference on the internal GPS receiver when using in or around 147. 0, 443. 8 MHz (Band A) and/or 438. 9 MHz (Band B). To eliminate the interference, swap Band A/ Band B or change the frequency. after the power supply is turned On, the clock data is automatically set and is updated once per day thereafter. When the Internal GPS receiver is On, pressing [POS] will display "Latitude longitude", then press [ OK] to cycle the display between "Time, Altitude, Travel direction, speed" >> "Target point distance, Travel direction" >> "Log meter" >> "GPS satellite information". · Press [ESC ] to return to the previous display. <Latitude longitude> INTERNAL GPS SETUP <Time, Altitude, Travel direction, speed> Internal GPS operation mode Enter Menu mode and access Menu 200. Altitude Travel direction Time Travel Speed GPS Only: The display shows only GPS information; The transceiver transmit and receive capabilities are turned OFF; only GPS operation is available. <Target point distance, Travel direction> Travel direction · Target point distance · · The " " icon appears when the function is turned ON, the " " icon appears when the function is turned OFF. Selecting "Yes" will clear the entire Track Log. Overwriting the Track Log When the Track Log becomes full, new data will begin overwriting the oldest Track Log data 1 Enter Menu mode and access Menu 221. When turning the Track Log function On, "Log Start" appears for approximately 5 seconds, followed by the "iLOG" icon. 2 Select "On" or "Off". Selecting "On" will allow old data to be overwritten with new data. · When setting Menu 200 to "GPS Only" and the Track Log function is turned On, the "" "" icon appears. · When turning the Track Log function Off, "Log Stop" appears on the display for approximately 5 seconds. · · With the Track Log function On, even if the power source is turned Off during Log acquisition, the log is backed up so that when the power is turned back on, the log acquisition resumes. You can verify the Log activity ratio in the GPS pinpointing screen. GPS ­ 4 LOG SETUP Track Log Acquisition Type You can set the conditions for saving portable Track information as GPS Logger. You can change the settings for travel speed, etc. 1 Enter Menu mode and access Menu 230. TARGET POINT You can register positional information for a target point. 1 Enter Menu mode and access Menu 240. 2 Select a Target Point (from 1 ~ 5). The "in use" target point mark ( ) appears to the left of the channel number. 2 Select "Time", "Distance", or "Beacon" for the Record Method. 4 Access Menu 241. 5 Enter a Target Point name (up to 8 characters). 4 Select an Interval time from 2 ~ 1800 seconds (in steps of 1 second). · The Interval setting is available only if the Record Method has been set to "Time". 5 Access Menu 232. <Menu No. 3W0: "dd°mm. mm' "> 6 Select a Distance from 0. 01 ~ 9. 99 (in steps of 0. 01). · · The Distance setting is available only if the Record Method has been set to "Distance". [. . . ] After pressing [#], press [0] to [9] to enter a frequency or memory channel number. SKY CMD ­ 3 WEATHER ALERT (TH-G71A ONLY) The Weather Alert is available only in the USA and Canada. When activated, this function will check for a received NOAA 1050 Hz tone. When the tone is received, the weather alert tone will sound. WEATHER ALERT ON/ OFF 1 Enter Menu mode and access Menu 13A. WEATHER ALERT SCAN The memory channel only for the weather alert is scanned. 1 Enter Menu mode and access Menu 13B. 2 Set the Weather Alert to "On" or "Off". · · When activated, the " " icon appears on the display. [. . . ]