User manual KENWOOD TK-6110

[. . . ] INSTRUCTION MANUAL VHF FM TRANSCEIVER TK-6110 © B62-1216-20 (K, K2) 09 08 07 06 05 04 03 02 THANK YOU! We are grateful you chose KENWOOD for your land mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. NOTICES TO THE USER ◆ GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. ◆ ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. [. . . ] Drill the holes, then attach the mounting bracket using the supplied 5 x 16 mm screws. • Be sure to mount the transceiver in a location where the controls will be within easy reach of the user and where there is sufficient space at the rear of the transceiver for cable connections. 2 Connect the antenna and the supplied power cable to the transceiver. 3 Slide the transceiver into the mounting bracket and secure it using the supplied hex-headed screws. 4 Mount the microphone hanger, using the supplied 4 x 16 mm screws, in a location where it will be within easy reach of the user. • The microphone should be mounted in a place where it will not interfere with the safe operation of the vehicle. 5 Connect the microphone cable to the jack on the front panel of the transceiver. Place the microphone on the hanger. Microphone Microphone hanger Microphone cable Mounting bracket Transceiver Antenna connector Hex headed screw Power input connector Power cable Fuse Black wire Fuse holder Red wire Battery 3 GETTING ACQUAINTED ■ Front Panel q Display w Speaker MON A B C SCN e r t y u i o !0 q Volume control Turn clockwise to increase the volume. Turn counterclockwise to decrease the volume. w / keys Press these keys to activate their programmable functions {page 7}. The default settings of these keys are “Channel Up” ( ) and “Channel Down” ( ). e Microphone jack Insert the microphone plug into this jack. r IO (Power) switch Press to switch the power ON. Press and hold for approximately 1 second to switch the power OFF. t MON key Press MON to activate its programmable function {page 7}. The default setting of this key is “Monitor”. y A key u B▼ key i C▲ key Press these PF (programmable function) keys to activate their programmable functions {page 7}. The default setting of these keys is “No Function”. o SCN key Press SCN to activate its programmable function {page 7}. The default setting of this key is “Scan”. Lights green while the selected channel is busy. 4 ■ Display Displays the operating Channel number, the Channel name, and the transceiver status. Displays the operating channel number and the channel status: P indicates a Priority channel HC indicates a Home Channel tA indicates Talk Around mode Flashes when a call is received by DTMF or 2-Tone signaling. Appears during and after transmitting if set by the dealer. Appears when signaling squelch is turned OFF. Appears when the optional scrambler board is enabled. Appears when the selected channel is in the scanning sequence. Appears when Operator Selectable Tone is enabled. 5 ■ Rear Panel TK-6110 15 pin connector (for accessories) Antenna connector Power input connector ■ Microphone PTT (Push To Talk) switch Press and hold to transmit, then speak into the microphone. [. . . ] ■ Time-out Timer (TOT) The TOT is used to automatically inhibit transmission after a specified time elapses. If the PTT switch is held down for longer than the programmed time, the transceiver will stop transmitting and a warning tone will sound. To stop the warning tone, release the PTT switch. ■ Busy Channel Lockout (BCL) BCL prevents you from interfering with other stations that may be using the same channel as you. [. . . ]