User manual KENWOOD TM-D700A

[. . . ] INSTRUCTION MANUAL 144/440 MHz FM DUAL BANDER TM-D700A TM-D700A TM-D700E 144/430 MHz FM DUAL BANDER 144/430 MHz FM DUAL BANDER KENWOOD CORPORATION © B62-1228-20 (K, E, M) 09 08 07 06 05 04 03 02 01 THANK YOU! We are grateful you decided to purchase this KENWOOD FM transceiver. KENWOOD always provides Amateur Radio products which surprise and excite serious hobbyists. This time KENWOOD presents a mobile with a built-in TNC to make data communications much more convenient than before. KENWOOD believes that this product will satisfy your requirements on both voice and data communications. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual. [. . . ] The keypad on the MC-53DM also is available to enter alphanumeric characters in step 6. See page 18. Note: x You can also name the Program Scan {page 52} and DTMF {page 60} channels, but you cannot name the Call channel {page 39}. x You can assign names only to memory channels in which you have stored frequencies and related data. x The stored names can be overwritten by repeating steps 1 to 10. x The stored names also are erased by clearing memory channels. 6 Turn the Tuning control to select the first digit. · You can enter alphanumeric characters plus special ASCII characters. 7 Press [a ]. a · The cursor moves to the next digit. 38 CALL CHANNEL The Call channel can always be selected quickly no matter what mode the transceiver is in. For instance, you may use the Call channel as an emergency channel within your group. In this case, the Call/VFO scan {page 54} will be useful. The default frequency stored in the Call channel is 144. 000 MHz for the VHF band. The default on the UHF band is 440. 000 MHz or 430. 000 MHz depending on the market versions. The Call channel can be reprogrammed either as a simplex & repeater or oddsplit channel. Note: Unlike channels 1 to 200 the call channel cannot be cleared. s Reprogramming the Call Channel 1 Select the desired band. 3 Select the desired frequency and related data (Tone, CTCSS, etc. ). · When you program the Call channel as an odd-split channel, select a receive frequency. 4 Press [F], [C. IN]. · The selected frequency and related data are stored in the Call channel. · When programming as an odd-split channel, press [F], [C. IN] (1 s) instead; "±" appears. 7 s Recalling the Call Channel 1 Select the desired band. 2 Press [CALL] to recall the Call channel. · "CALL" appears. To also store a transmit frequency, proceed to the next step. 5 Select the desired transmit frequency. 6 Press [C. IN]. · The transmit frequency is stored in the Call channel, and the previous mode is restored. Note: x Transmit Offset status and Reverse status are not stored in an odd-split Call channel. x To store data other than frequencies, select the data in step 3 not step 5. · To restore the previous mode, press [CALL] again. 39 MEMORY-TO-VFO TRANSFER You may sometimes want to search for other stations or a clear frequency, near the frequency stored in a memory channel or the Call channel. In this case first transfer the contents of a memory channel or the Call channel to the VFO. 1 Recall the desired memory channel or the Call channel. s 7 · The entire contents of the memory channel or the Call channel are copied to the VFO. Note: x A transmit frequency from an odd-split memory channel or odd-split Call channel is not transferred to the VFO. To transfer a transmit frequency, press [REV], then press [F], [MsV]. s x Lockout status and memory names are not copied from a memory channel to the VFO. [. . . ] 61 Frequencies, Selecting Microphone [UP]/ [DWN] . . 63 Memory Channel Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Lock All-control Lock . . . . . . . . . . . . . . . . . 67 Memory Channels Call Channel, Changing . . . . [. . . ]