User manual KENWOOD TM-331A

[. . . ] TM-D700A: 144/440 MHz FM Dual Bander (U. S. A. / Canada) TM-331A: 144/430 MHz FM Dual Bander (Europe) TM-D700A: 144/430 MHz FM Dual Bander (General market) · Is capable of receiving packet data on one band while receiving audio on the other band. · Enhanced Programmable Memory (PM) channels store virtually entire current operating environments for your quick recall. · Contains a total of 200 memory channels to program frequencies and other various data. Allows each memory channel to be named using up to 8 alphanumeric and special ASCII characters. [. . . ] To recall channel 3, for example, press [ENTER], [0], [0], [3]. Note: x When you recall an odd-split memory channel, "±" appears on the display. Press [REV] to display the transmit frequency. x After recalling a memory channel, you may program data such as Tone or CTCSS. These settings, however, are cleared once you select another channel or the VFO mode. To permanently store the data, overwrite the channel contents {page 36}. · To quit clearing the memory channel, press [ESC]. 4 Press [OK]. Note: x If you have recalled a memory channel on the non-control band (A or B), you cannot select the same channel on the control band to clear. x When in Channel Display mode, you cannot clear any memory channel. 37 NAMING A MEMORY CHANNEL You can name memory channels using up to 8 alphanumeric characters. When you recall a named memory channel, its name appears above the frequency. Names can be call signs, repeater names, cities, names of people, etc. cd 7 3 Press [c ]/ [d] to select "RADIO (1­)", then press [OK]. 4 Press [c]/ [d] to select "MEMORY (1­4­)", then cd press [OK]. 5 Press [c ]/ [d] to select "MEMORY NAME (1­4­4)", cd then press [OK]. · The display for entering a memory name appears; the first digit blinks. 8 Repeat steps 6 and 7 to enter up to 8 digits. Switches among the sets of alphanumeric characters, accented letters (TM-331A only), and special ASCII characters. 1 Recall the desired memory channel or the Call channel. s 7 · The entire contents of the memory channel or the Call channel are copied to the VFO. Note: x A transmit frequency from an odd-split memory channel or odd-split Call channel is not transferred to the VFO. To transfer a transmit frequency, press [REV], then press [F], [MsV]. s x Lockout status and memory names are not copied from a memory channel to the VFO. x If you recall the Call channel in step 1, simply turning the Tuning Control or pressing Mic [UP]/ [DWN] also transfers the contents to the VFO. The frequency, however, is changed by one step. CHANNEL DISPLAY When in this mode, the transceiver displays only memory channel numbers (and memory names if stored) instead of frequencies. 2 Press [c]/ [d] to select "RADIO (1­)", then press cd [OK]. 3 Press [c]/ [d] to select "MEMORY (1­4­)", then cd press [OK]. 4 Press [c]/ [d] to select "CHANNEL DISPLAY (1­4­ cd 2)", then press [OK]. 5 Press [c]/ [d] to switch the function ON (or OFF). cd 6 Press [OK] to complete the setting. 7 Press [MNU] to exit Menu mode. Note: You cannot switch this function ON unless you can recall any channel on both bands A and B. When in Channel Display mode, you cannot use the following functions: Sub-band Select Memory Store Memory-to-VFO Transfer VFO Scan PM Recall Partial/ Full/ PM Reset Frequency Step Size Change VFO Select PM Store 1/ 10 MHz Step Change All-control Lock 40 PARTIAL OR FULL RESET? If your transceiver seems to be malfunctioning, initializing the transceiver may resolve the problem. [. . . ] 58 Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Display Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Dual Tone Multi-Frequency (DTMF) Functions Making Calls . . . . . . . . . . . . . . . . . . . . . 60 Transmitting Stored Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]