User manual KENWOOD TR-7930 SERVICE MANUAL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual KENWOOD TR-7930. We hope that this KENWOOD TR-7930 user guide will be useful to you.

Lastmanuals help download the user guide KENWOOD TR-7930.


Mode d'emploi KENWOOD TR-7930
Download
Manual abstract: user guide KENWOOD TR-7930SERVICE MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] This transceiver features a Digital Signal Processing (DSP) unit to process IF and AF signals. By taking maximum advantage of DSP technology, the TR-7930 transceiver gives you enhanced interference reduction capabilities and improves the quality of audio. You will notice the differences when you fight QRM and QRN. As you learn how to use this transceiver, you will also find that Kenwood is pursuing "user friendliness". [. . . ] 4 Press [KEY (DELAY)] again to complete the setting. Note: When using the semi-automatic "Bug" function, the selected speed applies only to the rate that dots are sent. Invalid Break-In Operation You can make break-in operation invalid while performing the keying speed adjustment. To switch this function ON, access Menu No. 43, and select "on" (default is "oFF"). · "VOX" blinks when break-in operation is enabled. 33 7 COMMUNICATING AIDS RISE TIME OF CW The rise time of a CW signal is the time for the RF output to rise to its maximum power after the key is closed. 1 Press [MENU], then press [Q-M. IN]/ [Q-MR] or turn the MULTI/CH control to select Menu No. 2 Press [M. IN]/ [SCAN (SG. SEL)] to select "1", "2", "4", or "6" (default). · The default setting of 6 ms is fine for slow or medium keying speeds and normal weighting (dot/ dash ratio). 1, 2, or 4 ms are good for faster keying speeds. 3 Press [MENU] to exit Menu mode. CW MESSAGE MEMORY This transceiver has 4 memory channels for storing CW messages. Each memory channel can store approximately 50 characters (equivalent of 250 dots). These memory channels are ideal for storing contest exchanges that you want to send repeatedly. Semi-automatic keys are also known as "Bugs". When this function is ON, dots are generated in the normal manner by the electronic keyer. Dashes, however, are manually generated by the operator by holding the keyer paddle closed for the appropriate length of time. To switch this function ON, access Menu No. The default is OFF. Note: When the Bug Key function is ON, CW Message Memory (see below) cannot be used. 3 Begin sending using the keyer paddle. · The message you send is stored in memory. 4 To complete the message storage, press [CLR] or [CH1 (REC)]/ [CH2 (REC)]/ [CH3 (REC)]/ [RX/4 (REC)] to stop. · When the number reaches 100(%), the memory becomes full and recording automatically stops. Note: If you do not operate the keyer paddle after starting to record a message, a pause is stored in the channel. 34 7 COMMUNICATING AIDS Checking CW Messages without Transmitting 1 Press [CW/FSK (REV)] until you select CW mode. 2 If Break-in is ON, press [VOX (LEV)] to turn VOX OFF. 3 Press [CH1 (REC)], [CH2 (REC)], [CH3 (REC)], or [RX/4 (REC)] to select the channel to be played back. 56 is "oFF", press and hold the current playback channel key to repeatedly play back the message saved to that key (a display such as "CP 1111" appears for the channel key you pressed. ). To cancel the playback, press any channel key or [CLR]. [. . . ] 2 Press [A/B (A=B)] + [ ] to switch the transceiver ON. · A confirmation message appears on the display. 3 Turn the MULTI/CH control and select "VFO RESET". 78 15 TROUBLESHOOTING OPERATION NOTICES The transceiver has been designed and engineered to avoid possible hardware glitches. However, you may notice the following symptoms when you operate the transceiver. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD TR-7930

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD TR-7930 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag