User manual KENWOOD TS-570S

[. . . ] INSTRUCTION MANUAL PF HF TRANSCEIVER TS-570D ATT VOX SEND PRE-AMP PROC AT TUNE UP CH1 CH2 CH3 N. R. CW TUNE FILTER RIT/XIT MR M. IN ­ + 2 DSP SLOPE HIGH LOW LOW CUT AF 4 RF 6 PHONES MIC 1 ANT 2 REC 3 FINE PWR LSB USB DOWN 8 4 MIC 5 8 F. LOCK 6 KEY CW FSK 0 10 SPLIT FM AM TF-SET A/B RIT NB AGC/TONE REV CH IF SHIFT 4 SQL 6 7 CLR 9 DELAY M/V 1MHz SCAN A=B CLEAR XIT 2 8 MENU 0 ENT M>VFO M. IN 0 10 Intelligent Digital Enhanced Communications System ALL MODE MULTI-BANDER TS-570S TS-570D HF TRANSCEIVER KENWOOD CORPORATION © B62-1542-00 (K, E, M)(MC) 09 08 07 06 05 04 03 02 01 00 APPLICABLE MODEL This manual applies to the following model: TS-570S: All mode multi-bander TS-570D: HF Transceiver Intelligent Digital Enhanced Communications System NOTICE TO THE USER One or more of the following statements may be applicable to this equipment. FCC WARNING SUPPLIED ACCESSORIES Carefully unpack the transceiver. We recommend that you identify the items listed in the table below. In addition, it is safe to keep the box and the packing material. [. . . ] While transmitting, if you select a frequency outside the transmit frequency range, the transceiver is automatically forced to receive mode. If you selected transmit mode by pressing [SEND], transmission will not resume until you select a frequency inside the transmit frequency range, and you press [SEND] again. 0. 7 2. 2 Note: Audio frequency (kHz) "U" selectable in Menu No. The menu includes this selection because of a possible future enhancement. The figure above is given for your better comprehension. The actual profiles will be affected by factors such as the transmit IF filters. 33 8 COMMUNICATING AIDS CW BREAK-IN Break-in allows you to transmit CW without manually switching between transmit and receive modes. Two types of Break-in are available, Semi Break-in and Full Break-in. Semi Break-in: When the key contacts open, the transceiver automatically waits for the passage of the time period that you have selected. The transceiver then returns to the receive mode. Full Break-in: As soon as the key contacts open, the transceiver returns to the receive mode. ELECTRONIC KEYER This transceiver has a built-in electronic keyer that can be used by connecting a keyer paddle to the transceiver's rear panel. Consult "Keys and Keyboards for CW Operation" {page 3} for details regarding this connection. This built-in keyer supports lambic operation. CHANGING KEYING SPEED The keying speed of the electronic keyer is fully adjustable. Selecting the appropriate speed is important in order to send error-free CW that other operators can copy solidly. Selecting a speed that is beyond your keying ability will only result in mistakes. If you select a speed that is close to the speed used by the other station, you will obtain the best results. · · "CW" appears. 2 Press [KEY]. USING SEMI BREAK-IN OR FULL BREAK-IN 1 Press [CW/FSK] to select CW mode. · · · "CW" appears. The current setting (Full or delay time) appears. 3 Press [DELAY]. 4 Turn the MULTI/CH control to select Full Break-in or a delay time for Semi Break-in. · Available delay times are from 5 to 100 (50 ms to 1000 ms) in steps of 5. The transceiver automatically switches to the transmit mode. When Full is selected: The transceiver immediately switches to the receive mode when the key opens. [. . . ] 46 Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Time-operated . . . . . . . . . . . . . . . . . . . . . . . 47 Speaker, External (EXT SP) . . . . . . . . . . [. . . ]