User manual KENWOOD VR-60RS

[. . . ] AUDIO VIDEO SURROUND RECEIVER VR-60RS VR-50RS INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. About the supplied remote control Compared to standard remote controls, the remote control supplied with this model has several operation modes. These modes enable the remote control to control other KENWOOD DVD players. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] Confirm that all the speakers have been correctly selected. 5 Press the SETUP key to exit the SETUP mode. Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is "TAPE". To change the source to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE". Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. 2 Hold down the AUTO/MONO key for more than 2 seconds. · The source indication changes to "MD". · To return to the original indication, repeat procedure 2. Setting the speaker status The speaker indicator lights up. 1 Use the INPUT SELECTOR knob to select the source of which the input level you want to adjust. · You can store a separate input level for each input source. 2 Press the SOUND key repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to adjust the input level. Press the SPEAKERS ON/OFF key to switch the speaker on or off. · The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB. ) 4 Press the SOUND key again to return to the input indication. 18 EN Normal playback Listening to a source component Adjusting the sound 1 Use the INPUT SELECTOR knob or Input Selector keys to select the source you want to listen to. The input sources change as shown below: 1 2 3 4 5 6 7 "TUNER" "CD/DVD" "TAPE" or "MD" "VIDEO1" "VIDEO2" "DVD" "AUX" Adjusting the Tone (remote control only) You can adjust the sound quality when this model is in the PCM stereo and analog stereo mode. 1 Press the TONE key to select the Tone mode. 2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to select TONE ON/OFF. 2 Start playback from the selected source. 3 Use the VOLUME CONTROL knob or VOLUME %/fi keys to adjust the volume. 3 When in TONE ON selection, press the TONE key for the following displays. BASS : Select this to adjust the low frequency range. TREB : Select this to adjust the high frequency range. 4 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to adjust the sound quality. · The bass and treble levels are adjustable from -10 to +10 in 2 step increments. One-touch low frequency emphasis (Bass Boost) (remote control only) You can adjust the sound quality when this model is in the PCM stereo and analog stereo modes. · Press the key once to select the maximum (+10) low frequency emphasis setting. · TONE will automatically be turned ON. [. . . ] 28 µV (75 )/ 40. 2 dBf Total harmonic distortion (1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 5% (71. 2 dBf input) STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 7% (71. 2 dBf input) Signal to noise ratio (1 kHz, 75 kHz DEV. ) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 dB (71. 2 dBf input) STEREO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]