User manual KENWOOD VRS-5100

[. . . ] AUDIO VIDEO SURROUND RECEIVER VRS-5100 INSTRUCTION MANUAL KENWOOD CORPORATION About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-5473-18 01 C (E, X, Y) 0312 *5473/01-07/EN 1 04. 4. 20, 1:29 PM Before applying the power Units are designed for operation as follows. [. . . ] 1 Press the SOUND key to select the SOUND mode. 2 Use the MULTI CONTROL∞¥5 keys or TRIM∞/5 keys to select “TONE” and then press the SOUND key. DOLBY DEX NEO:6 DOLBY PLII DTS -ES AAC DISCRETE MATRIX 6. 1 ACTIVE EQ. AUTO L LFE C R SW Listening with headphones 1 Connect headphones to the PHONES jack. S BS RS 3 When in TONE ON selection, press the SOUND key for the following displays. BASS : Select this to adjust the low frequency range. TREBLE : Select this to adjust the high frequency range. 4 Use the MULTI CONTROL ∞¥5keys or TRIM∞/5 keys to adjust the sound quality. PHONES • The sounds from all speakers are cut off. DOLBY DEX NEO:6 DOLBY PLII DTS -ES AAC DISCRETE MATRIX 6. 1 ACTIVE EQ. AUTO L LFE C R SW LS S BS RS 2 Use the VOLUME CONTROL knob (or VOLUME +/- keys) to adjust the volume. • The bass and treble levels are adjustable from -10 to +10 in 2 step increments. • The adjustment item is displayed for approximately 20 seconds. 5 Press the SOUND key to accept the setting. 6 Use the MULTI CONTROL ∞¥5keys or TRIM∞/5 keys to select the “EXIT”. 7 Press the SOUND key to return to the input indication. 18 EN *5473/15-22/EN 18 04. 4. 20, 1:34 PM Recording Recording audio (analog sources) Listening to radio broadcasts The receiver can store up to 40 stations in the memory and recall them by one-touch operation. Radio stations can be classified into RDS (Radio Data System) stations and other stations. To listen to or store RDS stations in the preset memory see “Using RDS (Radio Data System)”. • The RDS function is only for the Europe. INPUT SELECTOR Tuning (non-RDS) radio stations INPUT SELECTOR MULTI CONTROL∞¥5 Recording a music source 1 Use the INPUT SELECTOR knob or Input Selector keys to select the source (other than “VIDEO1”) you want to record. 3 Start playback, then start recording. BAND BAND AUTO Recording video 1 Use the INPUT SELECTOR knob or Input Selector keys to select the video source (other than “VIDEO1”) you want to record. 2 Set the video deck connected to VIDEO1 to record. • Recording may not be normal for some video software. This is due to the copy guard condition. º TUNING 1¥¡ TUNER 1 Use the INPUT SELECTOR knob or TUNER key to select the tuner. 2 Use the BAND key to select the desired broadcast band. Each press switches the band as follows: 1 FM 2 AM “AM” or “FM” indicator appears in the display DIGITAL RDS PTY ST. TUNED AUTO FM/AM kHz MHz 3 Use the AUTO key to select the desired tuning method. Each press switches the tuning method as follows: 1 AUTO lit (auto tuning) 2 AUTO not lit (manual tuning) “AUTO” indicator lights up in the display. DOLBY DEX NEO:6 DOLBY PLII DTS -ES AAC DISCRETE MATRIX 6. 1 ACTIVE EQ. TUNED AUTO FM/AM kHz MHz L LFE C R SW LS S BS RS • Normally, set to “AUTO” (auto tuning). If the radio waves are weak and there is a lot of interference, switch to manual tuning. (With manual tuning, stereo broadcasts will be received in monaural. ) 4 Use the MULTI CONTROL ∞/ 5 keys or TUNING 1 / ¡ keys to select the station. “ST. ” lights when a broadcast is being received in stereo. DOLBY DEX NEO:6 DOLBY PLII DTS -ES AAC DISCRETE MATRIX 6. 1 ACTIVE EQ. [. . . ] 1. 3 µV / 13. 2 dBf (40 kHz DEV. , S/N 26 dB) STEREO . . . . . . . . . . . . . . 45 µV / 42. 1 dBf (40+6 kHz DEV. , S/N 46 dB) Total harmonic distortion (DIN at 1 kHz) MONO (1 kHz, 40 kHz DEV. ) . . . . . . . . . . . . . . . . . . . . . 0. 3% (65. 2 dBf input) STEREO (1 kHz, 40+6 kHz DEV. ) . . . . . . . . . . . . . . . 0. 8% (65. 2 dBf input) Signal to noise ratio (DIN weighted at 1 kHz) MONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]