User manual KENWOOD XD-8551

[. . . ] AC 110 / 127 / 220 / 230 240 V switchable* * AC voltage selection The AC voltage selector switches on the rear panel are set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting positions of these switches match your line voltage. If not, they must be set to your voltage in accordance with the following direction. AC voltage selector switches Turn the selector to match your line voltage with a small screwdriver or other pointed tool. [. . . ] edly until the desired track number is shown. · To start playback from a desired track, press the P CALL 4 1 or ¡ ¢ button whilst in . the stop mode to select the track number, and then press the 3 button. 3 P. CALL 41 ¡¢ Note : · Tracks skipping can only search for music on a single disc. 16 EN Cue and review 1 Load a disc and begin playback. 2 Hold down the P CALL ¡ ¢ button for audi. P. CALL 41 ¡¢ 7 STOP ble fast forward, and hold down the P CALL . 3 Normal playback will resume when the P CALL . 4 1 or ¡ ¢ button is released. Notes : · When the end of the disc is reached whilst cueing, "END" will appear in the display and CD operation will be paused. (Even though the next disc has been loaded, the disc will not be switched. ) Press the P CALL 4 1 button for fast re. verse or press the 7 STOP button to stop CD operation. · If the beginning of the disc is reached whilst reviewing, the mode will automatically switch to normal playback at that point. 7 P. CALL 41 ¡¢ Repeat play All tracks on up to 3 discs, or a programmed sequence can be continuously repeated. To repeat all tracks on up to 3 discs : 7 STOP 3 Press the 3 button twice. · "RPT. " will light up on the display. To repeat a programmed sequence : 1 Programme a sequence of up to 32 tracks. (see page 18) 2 Press the 3 button again. 3 Within 30 seconds, press the P CALL (4 1 . · MEMORY/ SET P. CALL 41 ¡¢ 4 · 5 · MEMORY/ SET P. CALL 41 ¡¢ or ¡ ¢) button to make the preset channel number flash in the display. The order of the station stored in memory, starts with preset channel 1. Within 30 seconds, press the MEMORY/SET button to store that station in the selected station preset number memory. If the "PGM" and preset number go out before the station is memorized, repeat the operation from step 2. Repeat steps 1 - 4 to set other preset stations, or to change a preset station. When a new station is stored in the selected station preset number memory, the previous stored contents will be erased. To recall a memorized station : Press the P CALL (4 1 or ¡ ¢) button for . less than 0. 5 second to select the desired station. · The stations (preset channel number, frequency band) which have been stored in memory will appear in the display in numerical order, irrespective of the frequency bands. Notes : · When searching for a memorized station, do not press the P CALL (4 1 or ¡ ¢) for . · When the P CALL (4 1 or ¡ ¢) button . is pressed for more than 0. 5 second, the unit will enter the preset memory scan mode. Backup function : The backup function protects all station presets for a few hours should there be a power failure or the AC power cord is removed from the AC socket. 20 EN Preset memory scan The stations saved in the preset memory can be scanned automatically. [. . . ] ­ ­ Consult the dealer or an experienced radio / TV technician for help. 31 EN SPECIFICATIONS (XD-8551 / XD355) Main Unit [Amplifier section] Rated power output 1 kHz, 1% T. H. D. , 6 . . . . (RMS) 38. 5 W + 38. 5W Effective output power during STEREO operation 1 kHz, 10% T. H. D. , 6 . . . . . . . . . . (RMS) 50W + 50W Signal to noise ratio VIDEO/AUX INPUT . . . . . . . . . . . . . . . . . . . . . 88 dB (IHF' 66) Input sensitivity / impedance VIDEO/AUX INPUT . . . . . . . . . . . . . . . . . . . . [. . . ]