User manual KETTLER IMPERIAL

[. . . ] Keep these instructions in a safe place for maintenance purposes or for ordering spare parts. All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In order to offer our customers the very best in product quality, we reserve the right to make technical changes at any time. In spite of this, should you have any cause for complaint, please contact KETTLER. Note on Safety The table-tennis table should be used only for its intended purpose, Instruct other persons (in particular children) using the table in i. e. [. . . ] In most cases, a slightly dampened cloth is sufficient. Waste Disposal: KETTLER products are recyclable. To protect your outdoor table keep it closed and covered by the KETTLER table tennis cover (item # 7032-400) when not in use. its useful life please dispose of this article correctly and safely (local refuse sites). Instructions for Assembly The equipment must be assembled with due care by two adult play with plastic bags! The fastening material required for each assembly step is shown persons. Ensure that you have received all the parts required (see check list) and that they are undamaged. Should you have any cause for complaint, please contact your KETTLER dealer. Before assembling the equipment, study the drawings carefully in the diagram inset. Use the fastening material exactly as instructed. Bolt all the parts together loosely at first, and check that they and carry out the operations in the order shown by the diagrams. The correct sequence is given in capital letters. Please note that there is always a danger of injury when work- ing with tools or doing manual work. Therefore please be careful when assembling this machine. Ensure that your working area is free of possible sources of dan- have been assembled correctly. Tighten the locknuts by hand until resistance is felt, then use wrench to finally tighten nuts completely against resistance (locking device). Then check that all screw connections have been tightened firmly. Attention: once locknuts have been unscrewed they no longer function correctly (the locking device is destroyed), and must be replaced. For technical reasons, we reserve the right to carry out prelimi- ger, for example don't leave any tools lying around. Always dispose packaging material in such a way that it may not cause any danger. There is always a risk of suffocation if children nary assembly work (e. g. addition of tubing plugs). Please keep original packaging of this article, so that it may be used for transport at a later date, if necessary. List of spare parts When ordering spare parts, always state the full article number, sparepart number, the quantity required and the S/N of the product (see spare parts drawing). Important: spare part prices do not include fastening material; if fasten2 ing material (bolts, nuts, washers etc. ) is required, this should be clearly stated on the order by adding the words , , with fastening material". For parts and service ONLY call 866. 804. 0440 or send email to parts@kettlerusa. com KETTLER International Inc. · 1355, London Bridge Road · Virginia Beach, VA 23453 USA KETTLER LIMITED WARRANTY THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THE MANUFACTURER ON KETTLER PRODUCTS, EXCEPT THE MANUFACTURER'S LIMITED WARRANTY AGAINST DEFECTS IN MATERIAL SET OUT BELOW: This KETTLER Limited Warranty applies to products sold through the KETTLER Authorized Dealer Network to the original retail purchaser and authenticated by proof of purchase from a retailer located in the United States. Any shipments made under this warranty will be shipped to the United States only. Any shipment outside of the United States will be at the sole cost of the customer. This KETTLER Limited Warranty is a manufacturer's warranty and is not changed or modified by additional warranties extended by individual retailers at the point of sale. [. . . ] Again, ensure that the table cannot slip or tilt over! 11 17 Lowering the table halves Press the left-hand tip lock and turn the locking toggle into position. Hold the table firmly with one hand, press the right-hand lock and lower the table-half slowly into position. Never allow it to drop down! C A B 18 2x A C T U 3x AL S IZE 12 19 Folding the table halves B A Press the locking lever up and lift the table half upwards. Continue to press the lever during the first part of the upward motion. 20 15cm 13 14 21 B A max 1 cm = ok. max 1 cm = ok. click! max 1 cm = ok. Spare parts drawing and list 07162-490 1 4 2 USA Type label ­ Serial number HEINZ KETTLER GmbH & Co. [. . . ]