User manual KLIPSCH LIGHT SPEAKER SYSTEM

[. . . ] Tech Support: 1-800-KLIPSCH One complete system that installs in 30 minutes or less! State-of-the-art LIGHT & SOUND OWNER'S MANUAL AND INSTALLATION INSTRUCTIONS 1 Tech Support: 1-800-KLIPSCH The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Le symbole de l'éclair fléché dans un triangle équilatéral, a pour but d'avertir l'utilisateur de la présence non isolées d'une «tension dangereuse» dans le boîtier du produit que mai d'une magnitude suffisante pour constituer un risque d'électrocution pour les personnes. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Le point d'exclamation dans un triangle équilatéral sert à alerter l'utilisateur de la présence d'importantes exploitation et de maintenance (entretien) dans la documentation accompagnant l'appareil. Caution marking is located at the side of the apparatus. [. . . ] The Small LED light on the speakers will begin to flash red and will turn green when the pairing is complete. The transmitter will automatically find each speaker and assign it to its proper zone. 22 Tech Support: 1-800-KLIPSCH 5) If after 1 minute the LED on the LightSpeaker® has not turned "GREEN", repeat steps 1-4. a) If after 2 attempts the LED on the LightSpeaker® fails to turn green, try relocating the Transmitter closer to the LightSpeaker® Step 10: Plugging in your sources. Using the supplied audio cords, plug your MP3, CD Player, television or other desired sources to the back of the transmitter. Attach 1 or 2 audio sources. MP3 A) Locate the sources you want to use. They will have audio level outputs on them. Typically these are RCA or stereo headphone type jacks. You will need to have the proper cable from the source you want to attach to the Transmitter. You have two choices: 1) RCA to RCA cable 2) RCA to Stereo Mini Plug Cable 23 Tech Support: 1-800-KLIPSCH CAUTION!Do not use the speaker outputs as this can damage the transmitter!B) If you are attaching only one source it may be attached to either input but may be convenient to attach to source one. 1) You may use either the mini-plug or the RCA inputs on either source but only one input may be used at a time. The remote control and the transmitter are controlled in exactly the same manner. When you push a button on the remote contol the small LED next to the button will light up and remain lit until you push another button affecting either that zone or that source. The LEDs that are lit will tell what action the remote or transmitter is currently set to control. Step 11: Enjoy your LightSpeakers®! 24 Tech Support: 1-800-KLIPSCH Operating the Transmitter and Remote Control: The remote control and the transmitter are controlled in exactly the same manner. When you push a button on the remote contol the small LED next to the button will light up and remain lit until you push another button affecting either that zone or that source. The LEDs that are lit will tell what action the remote or transmitter is currently set to control. Here are the steps to take to operate the Transmitter and Remote Control: A) Press the zone you want to control B) When the LED next to the button lights, that zone is active and will be playing the source that is currently lit. To change to a different source simply press the source with the "unlit" LED until the LED next to the source you are choosing lights. C) Pressing Light once makes the light go On/Off D) Pressing the + arrow above the light "on" button will increase the brightness of the light. Pressing the "-" arrow below the light on/off button will dim the 25 Tech Support: 1-800-KLIPSCH light. [. . . ] Proof of purchase in the form of a bill of sale or receipted invoice from an authorized dealer, which is evidence that this product is within the Warranty period, must be presented or included to obtain Warranty service. This Warranty is invalid if (a) the factory-applied serial number has been altered or removed from this product or (b) this product was not purchased from a KLIPSCH authorized dealer. You may call 1-800-KLIPSCH to confirm that you have an unaltered serial number and/or you purchased from a KLIPSCH authorized dealer. This Warranty is only valid for the original purchaser and will automatically terminate prior to expiration if this product is sold or otherwise transferred to another party. [. . . ]