User manual KOBIAN CYPERPIX S930X

[. . . ] 1 Table of Contents Welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -Contents of Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 -Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The camera is ready to take the next picture. 13 Set Up Mode Startup Screen (Default: Default Screen ) You can select your favorite picture which you taken and saved in the camera. Use [ ][ ][ Photo" mode, press [Menu] button. ][ ][ ] to select " Metering", and then press [Set] button. ][ ][ ] to select the what you want, and then press [Set] button. Center-weighted average Very limited range in the center of the screen Automatic selection of the focus area where the subject closest to the camera is located Use this metering method when you want to exert some control over exposure, without leaving settings totally up to the camera. Pattern Average Using the Flash Perform the following steps to select the flash mode you want to use. In the " monitor. Photo" mode, press [Set] button to select the flash mode. 2. Each press of [Set] button cycles through the flash mode settings shown below on the LCD 3. Record the image. Auto The flash Force Off The flash does not fire. Force On Red-eye reduction, Auto The flash fires automatically as required by the lighting level. The flash fires automatically as required by the lighting level, and the flash pre-strobes before shooting to reduce red-eye phenomenon. NOTE You may not be able to achieve the desired results using a flash if the subject is too close or too far away. About red-eye reduction Using the flash to record at night or in a dimly lit room can cause red spots inside the eyes of people who are in the image. This is caused when the light from the flash reflects off of the retina of the eye. When red-eye reduction is selected as the flash mode, the camera performs 16 two pre-flash operations, one designed to cause the irises in the eyes of any people in the image to close, and one for the Auto Focus operation. This is followed by another flash operation for actual recording of the image. Set Up Mode Exposure Compensation (EV Shift) Adjust the exposure compensation setting to compensate for certain light conditions including: backlighting, indirect indoor lighting, and dark backgrounds. To cancel EV Shift, adjust the value until it becomes 0. 0. Use [ ][ ] to adjust the value what you want you want. Adjusting White Balance When the white balance mode is set to match the light source, the camera reproduces colors more accurately. Use [ ][ ][ Photo" mode, press [Menu] button. ][ ][ ] to select " White Balance", and then press [Set] button. ][ ][ ] to select the what you want, and then press [Set] button. Auto Day light Shade Tungsten Fluorescent Settings are automatically set by the camera For recording outdoors on a bright day For recording under overcast, shady or twilight skies For recording under tungsten lighting For recording under fluorescent lighting Using the Self-Timer The self-timer lets you select either a 2-second, 10-second, 30-second or 50-second delay of the shutter release after you press the [Shutter] button. 1. Use [ ][ ][ Photo" mode, press [Menu] button. ][ ][ ] to select " Self-Timer", and then press [Set] button. ][ ][ ] to select the setting you want, and then press [Set] button. 5. Record the image. 17 Quick View (default: ON ) Display image on the LCD after taking a picture. Set Up Mode Deleting Pictures, Video and Audio Step 1: Turn the mode switch to " button. Step 3: Use [ Step 4: Use [ ][ ][ ] to select " ] to select " Delete current" or " Delete all", and press [Set] button. ][ ][ ][ ] to select " Delete", and press [Set] Step 2: Hit the [Menu] button, then use [ " to delete, and press [Set] button. 18 Taking Pictures Step 1. Turn the camera on, with the mode switch set to " Photo" mode. Step 2. Frame your target through the LCD display. Step 3. [. . . ] You can now drag-and-drop files to your PC. 29 Download Photos Downloading Photo Using PhotoImpression 4. 0 As a USB Mass Storage Device, with the camera connected, its memory will simply appear as a disk drive to the host computer. Any files can be copied to and from the camera's memory, just like any other file on any other disk drive. For Windows 98SE user, please go to Microsoft www. microsoft. com to update Windows for Mass Storage Function Support. Turn on the camera and connect with USB cable, the camera will set at "Mass Storage" mode. 1. Click "PhotoImpression 4. 0" icon on desktop. 2. [. . . ]