User manual KOCOM KC-C61

[. . . ] If installed during winter season at temperature below -5condensation might be generated inside monitor and , camera due to temperature difference between indoors and outdoors. To prevent breakdown due to such condensation, connection should be made in 2 hours or more after installation. Do not install monitor and camera in locations subject to direct heating as harmful gases may subsequently be emitted in significant amounts. C-Mic Camera Lens Power Lamp To check power ON/OFF status To communicate with Monitor Clear picture quality realized by adopting 1/3" CCD Call Button By pressing the button, the related house will be called. Speaker Stop up P. V. C. pipe using adiabatic substances, to prevent air circulation Stopping up pipe as above minimizes temperature difference between indoors and outdoors, and also eliminates moisture and condensation on door camera window. When visitor calls, the voice from monitor comes out of the speaker. Option notice Don't install the set on a weak or ceiling surface such as plaster or press board, please install the set on the hard wall or ceiling like firm timber or concrete. Video Doorphone Wiring Diagram Wiring Diagram Door camera Installation Surface-mounting Door Camera Installation DOOR CAMERA INSTALLATION Wall Screw(4x10mm) Upward control groove Straight Ahead Installation After attach the body supporter with 2 screws(4x10mm), put the Door Camera into the grooves of body supporter, and then fix it with a screw(2. 6x6mm). bady support Screw(2. 6x6mm) Upward support Camera Front (Option) Caution for wiring Wiring between videophone and camera is 4 wire in polarity and use 0. 65mm or more single cable Connecting wiring between monitor and door camera should not be installed near other electrical cable, norbe horizontal. (In such case, clear picture can not be expected due to interruption by electrical noise) Upward control groove Looking "Upward" Installation After attach the body supporter with 2 screws(4x10mm), insert the upward support into the upward groove of body supporter, and then fix it with a screw(2. 6x6mm). Standard Height of Door Camera Bottom base of One hall Box Surface mount Standard height of the door camera is 1, 400mm 1, 450mm from the bottom of one camera to the floor. [. . . ] If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. The lighting flashwith arrowhead sysmbol, Within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous vollage` with in the product `s enclosure that may be of sufficient magnitube arisk of electric snock to persons. 22. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The exclarnation point with in a equilateral triangle, is intended to alert the user to the presence of important operating and maintenance(Servicing)instructions in the literature accompanying the appliance. Alternate Warnings - This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. [. . . ] please read this manual thoroughly to ensure correct usage, before operating Metal Pinhole Camera KC-D30 www. kocom. co. kr e-mail:export@kocom. co. kr www. kocominc. com(us) e-mail:sales@kocominc. com(us) Option 3. While you communicate with the visitor through camera, if the call from guardroom is made, the melody sound is ringing. And you can communicate with guardroom by pressing guardroom or communication button after finishing the communication with visitor. 2. While you communicate with guardroom, if the chime sound from the camera is made the screen is on, then you can check the visitor. (The screen is on for 30 seconds and automatically off) At this time, if you press camera or communication button, the communication with guardroom is ended and you can communicate with the visitor through the camera. 1. In case the monitor is connected to the guardroom, if you press the guardroom button, the signal is made and if the person in guardroom answers, you can communicate. [. . . ]