User manual KODAK DC265

[. . . ] KODAK DC265 Zoom Digital Camera User's Guide for the camera and Kodak software Visit Kodak on the World Wide Web at www. kodak. com Kodak, and FlashPix are trademarks of Eastman Kodak Company. Digita is a trademark of FlashPoint Technology, Incorporated. The FlashPix format is defined in a specification and test suite developed and published by Kodak in collaboration with Microsoft, Hewlett-Packard, and Live Picture. Only products that meet the specification and pass the test suite may use the FlashPix name and logo. Table of Contents Page Getting started . [. . . ] The pictures that are stored on the memory card appear on the television screen. 7 Scroll through your pictures using any of the three methods described in the "Viewing pictures" section on page 4-7. If pictures do not appear on the television, you may need try a different channel or adjust the Video preference on the camera. Refer to page 4-5. 4-18 5 5Connecting your camera to your computer 5 Connecting A first step to using your digital pictures on your computer is to connect your camera to your computer. The camera can communicate with your computer using: an RS-232 serial connection a Universal Serial Bus (USB) connection an IrDA (infrared) transceiver While in Connect mode, the camera is controlled by the computer. Except for the Mode dial, Power, Shutter, and Zoom buttons, all other camera buttons are disabled. The Ready light indicates when the camera is on. Once software is installed and the camera is connected to a computer, you are ready to transfer the pictures. Use the AC adapter when connecting to your computer to conserve battery power. 5-1 Which connection? The connection you use depends on several variables. You need to determine which connections are available with your Operating System, which of these connections are physically supported by your computer, and then you can make the connection. After making the connections, if you experience problems, refer to the troubleshooting guide located on the CD. Determining which connections are available This section guides you through what connections are available with your operating system. WINDOWS 95 If your computer uses a WINDOWS 95 Operating System, you need to determine which version. To check for the WINDOWS 95 version: 1 Click Start Settings Control Panel. 3 Click the General tab and note the installed Operating System: 4. 00. 950 indicates WINDOWS 95 (basic) 4. 00. 950a indicates WINDOWS 95a 4. 00. 950B indicates WINDOWS 95B The two types of connections available with WINDOWS 95 and 95a are: Serial--see "Checking for RS-232 serial support" on page 5-5, then "Using a serial cable to connect" on page 5-7. IrDA (infrared) transceiver--see "Checking for IrDA transceiver support" on page 5-6, and then see "Using an infrared transceiver to connect" on page 5-8. WINDOWS 95 and WINDOWS 95a require an IrDA Software Patch that is available from the Microsoft Web site. Go to http:// www. microsoft. com and then search for "irda. " (Please read and understand all the instructions provided by Microsoft before proceeding. ) 5-2 The two types of connections available with WINDOWS 95B are: Serial--see "Checking for RS-232 serial support" on page 5-5, then see "Using a serial cable to connect" on page 5-7. IrDA (infrared)--see "Checking for IrDA transceiver support" on page 56, and then "Using an infrared transceiver to connect" on page 5-8. The IrDA driver for WINDOWS 95B is either preloaded on your system or available on your original diskettes or CD. USB is not fully supported on WINDOWS 95. If you use USB on WINDOWS 95 and experience problems, please upgrade to WINDOWS 98. 5 Connecting WINDOWS NT 4. 0 WINDOWS NT 4. 0 supports only a serial connection, see the procedure, "Checking for RS-232 serial support" on page 5-5, then "Using a serial cable to connect" on page 5-7. WINDOWS 98 The three types of connections available for WINDOWS 98 are: Serial--see "Checking for RS-232 serial support" on page 5-5, then see "Using a serial cable to connect" on page 5-7. USB--see "Checking for USB support" on page 5-4, and then "Using a USB cable to connect" on page 5-8. IrDA (infrared)--see "Checking for IrDA transceiver support" on page 56, and then "Using an infrared transceiver to connect" on page 5-8. MACINTOSH Computers A serial or USB connection is available using the DIGITA Desktop Acquire (Plug-in). Refer to the online information provided with the software. 5-3 Determining what your computer supports Checking for USB support The Universal Serial Bus (USB) is a relatively new method for your camera to communicate with the PC. A USB connection is faster than an RS-232 serial connection, increasing the maximum data transfer rate to 12 Mb/sec. USB requires special computer hardware and software features, including a USB enabled motherboard, USB connections, and WINDOWS 98. Most computers manufactured prior to January 1997 do not meet these requirements. To determine if your computer supports a USB connection: 1 Verify that a USB connector is present. [. . . ] THIS WARRANTY DOES NOT COVER: CIRCUMSTANCES BEYOND KODAK'S CONTROL; SERVICE OR PARTS TO CORRECT PROBLEMS RESULTING FROM THE USE OF ATTACHMENTS, ACCESSORIES OR ALTERATIONS NOT MARKETED BY KODAK; SERVICE REQUIRED AS THE RESULT OF UNAUTHORIZED MODIFICATIONS OR SERVICE; MISUSE, ABUSE; FAILURE TO FOLLOW KODAK'S OPERATING, MAINTENANCE OR REPACKAGING INSTRUCTIONS; OR FAILURE TO USE ITEMS SUPPLIED BY KODAK (SUCH AS ADAPTERS AND CABLES). KODAK MAKES NO OTHER WARRANTIES, EXPRESS, IMPLIED, OR OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR THIS EQUIPMENT OR SOFTWARE. REPAIR OR REPLACEMENT WITHOUT CHARGE ARE KODAK'S ONLY OBLIGATION UNDER THIS WARRANTY. KODAK WILL NOT BE RESPONSIBLE FOR ANY SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM THE PURCHASE, USE, OR IMPROPER FUNCTIONING OF THIS EQUIPMENT REGARDLESS OF THE CAUSE. [. . . ]