User manual KODAK DP2000

[. . . ] User's Guide KODAK DP2000 Digital Projector with KODAK Image Manager Software FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Canada This Class A digital apparatus complies with Canadian ICES-003. [. . . ] · Press the left navigation button on the keypad to increase the amount of green in the image. · Press the right navigation button on the keypad to increase the amount of red in the image. Color The color setting adjusts a video image from black and white to fully saturated color. Press the left mouse button to decrease the amount of color in the image. · Press the right mouse button to increase the amount of color in the image. · Blank Screen Blank Screen determines what color is displayed when there is no active source and when the projector is in standby. Click the left or right navigation button to toggle between blue and black. Reset All Click the left or right navigation button to reset all the options (except Language, Video Standard, Rear Projection, and Standby Time) in all the menus to their original settings. Audio Menu Volume Note: Changing the volume from the menu is the same as changing it using the keypad. · Press the left navigation button to decrease the volume. · Press the right navigation button to increase the volume. Volume adjustments you make are saved for each source. 27 User's Guide KODAK DP2000 Digital Projector Image Menu Auto Image Note: Some screen savers interfere with the operation of Auto Image. If you're experiencing problems, try turning your screen saver off, then turning Auto Image off and back on. The projector automatically adjusts tracking, signal synchronization and vertical and horizontal position for most computers (Auto Image does not apply to video sources). If you want to adjust these features manually, you must turn off Auto Image first by highlighting Auto Image in the Image menu and clicking either the left or right navigation button to select "off". Auto Resize Auto Resize automatically resizes the image by scaling it up. It only affects computer images that are not the projector's native resolution. When Auto Resize is on, the projector makes the best fit of the image to the screen. If you turn Auto Resize off (by highlighting it in the Image menu and clicking the left or right navigation button to select "off"), the image may be either cropped or too small for the screen. 28 Using the Projector Manual Sync Note: The Manual Sync option is available only for computer sources. The projector sets this option automatically for a video source. The projector adjusts signal synchronization automatically for most computers. But if the projected computer image looks fuzzy or streaked, try turning Auto Image off then back on again. If the image still looks bad, try adjusting the signal synchronization manually: 1. Highlight Manual sync, then press the left or right navigation button repeatedly until the image is sharp and free of streaks. [. . . ] Position 29 Manual Sync 29 Manual Tracking 29 Vert. Position 30 K Kensington lock 41 keypad using 23 keypad buttons menu 24 standby 24 volume 24 KODAK Image Manager 35 L lamp turns off unexpectedly 45 lamp hour counter 34 Language menu 33 language, selecting for menus 33 laptop activation sequence 49 lens cleaning 37 M Macintosh computers compatibility 5 Menu button 25 menus. See on-screen menus monitor, colors don't match 45 mouse, connecting 14 N NTSC video 30 64 Index O on-screen menus Audio menu 27 changing functions 25 changing language of 33 Controls menu 30 Display menu 26 displaying 25 Image menu 28 Language menu 33 Status menu 33 P PAL video 27, 30 Plug and Play 32 power cord connecting 17 power up sequence 17, 43 project from behind the screen 31 R rear projection 31 relative humidity 47 remote control operating the disk mouse 22 using 21, 23 re-positioning image on screen 29 resetting adjustments 27 resolution 5 S safety guidelines 1 SECAM video 27, 30 security feature 41 service numbers 9 setting up 11 SimulScan with PowerBooks 60 specifications 47 Standby button 24 Standby Time 31 startup screen 32 Status menu 33 support numbers 9 S-video, connecting 15 T temperature limits 47 test pattern 43 text not visible 42 tint, adjusting 27 turning off the projector 18 turning on the projector 17 U USB mouse 14 V vertical lines displayed 29, 44 video 27 mirroring PowerBook 59 video standards 30 volume adjusting 24 W warranty 10, 67 weight 47 Z zooming the image 20 65 WARRANTY TIME PERIOD Kodak warrants the KODAK DIGITAL SCIENCE DP2000 Digital Projector (excluding lamps) to be free from malfunctions and defects in both materials and workmanship for two years from the date of purchase. WARRANTY REPAIR COVERAGE This warranty will be honored within the geographical location that the product was purchased. If the equipment does not function properly during the warranty period due to defects in either materials or workmanship, Kodak will, at its option, either repair or replace the equipment without charge, subject to the conditions and limitations stated herein. [. . . ]