User manual KODAK EASYSHARE Z8612 IS

[. . . ] When the Shutter button is pressed halfway, faces are detected, the scene is analyzed, and the best settings are applied. (See page 20). Capture modes Capture mode Smart Scene P A S M ISO SCN Scene Video Program Aperture priority Shutter priority Manual High ISO People in low-light scenes. Point-and-shoot simplicity under special conditions. Panorama "Stitching" 2 or 3 pictures into 1 panoramic scene. (See page 4. ) www. kodak. com/go/z8612support 9 Doing more with your camera Using optical zoom Use optical zoom to get up to 12X closer to your subject while taking pictures/videos. [. . . ] Capture + for other picture-taking settings. Available only in PASM and Panorama modes. to highlight a setting, then press the OK button. 3 Press 4 Choose an option, then press the OK button. NOTE: Press the Info button for information about camera settings and options. Some capture modes offer limited settings. www. kodak. com/go/z8612support 19 Using the advanced features Using PASM modes Use PASM modes when you want more control over your camera and pictures. Mode When to use Program mode offers the ease of auto shooting with full access to all menu options. The camera automatically sets the shutter speed and aperture (f-stop) based on the scene lighting. Press control to Exposure compensation (how much light enters the camera), flash compensation, and ISO Program speed Use Aperture Priority mode to control depth of Aperture, exposure compensation, flash field (the range of sharpness). The aperture compensation, and ISO speed Aperture setting may be affected by optical zoom. Priority P A S Shutter Priority M Manual Shutter Priority mode is primarily used to prevent blur when your subject is moving. The camera automatically sets the aperture for proper exposure. (To prevent blur, use a tripod for slow shutter speeds. ) Manual mode offers the highest level of creative control. (To prevent blur, use a tripod for slow shutter speeds. ) Shutter speed, exposure compensation, flash compensation, and ISO speed Aperture, shutter speed, flash compensation, and ISO speed NOTE: Settings you change in P, A, S, or M modes apply only to pictures taken in those modes. The settings, including Flash, are maintained for P, A, S, and M modes--even when you change modes or turn off the camera. Use Reset Camera (in the Setup menu) to reset P, A, S, or M mode to its default setting. 20 www. kodak. com/go/easysharecenter Using the advanced features Changing P, A, S, or M mode settings Aperture Shutter speed ISO speed Flash compensation Exposure compensation 1 Turn the Mode dial to P, A, S, or M. 2 Press to access available settings: Aperture--(also known as f-stop) control the size of the lens opening, which determines the depth of field. Smaller f-stop numbers indicate a larger lens opening; good for low-light. Larger f-stop numbers indicate a smaller lens opening; keeps the main subject sharp; good for landscapes and well-lit conditions. Shutter speed--control how long the shutter stays open. (Use a tripod for slow shutter speeds. ) Exposure Compensation--adjust the exposure. Use only a USB-certified computer equipped with a current-limiting motherboard. Contact your computer manufacturer if you have questions. If using this product in an airplane, observe all instructions of the airline. When removing the battery, allow it to cool; it may be hot. Follow all warnings and instructions supplied by the battery manufacturer. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving antenna; 2) increase the separation between the equipment and the receiver; 3) connect the equipment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/TV technician for additional suggestions. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Where shielded interface cables have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulation. www. kodak. com/go/z8612support 25 Appendix Waste Electrical and Electronic Equipment labeling EU: It is the final user's responsibility to discard this equipment into an approved, segregated collection scheme to enable its suitable treatment/disposal and to improve human/environmental protection. For more information, see your retailer, local authority, or www. kodak. com/go/recycle. [. . . ]