User manual KODAK EKTAGRAPHIC III SERVICE MANUAL

[. . . ] {ServiceManual}{Production}{KodakServiceSupport} Publication No. SM4530-1 30APR96 SERVICE MANUAL for the Kodak Ektagraphic III PAINTED and NON-PAINTED PROJECTORS Models A, KKA, JA, ATS, AM, AMT, JAMT, B, BR, E, E-PLUS SLIDE, J-E PLUS, and KKE PLUS Kodak Home Page on Internet Intranet Table of Contents A100_0001HA © Eastman Kodak Company, 1999 PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the subject matter gained by Eastman Kodak Company prior to publication. No patent license is granted by this information. Eastman Kodak Company reserves the right to change this information without notice, and makes no warranty, express or implied, with respect to this information. [. . . ] [3] Place the MECHANISM ASSEMBLY on the MECHANISM RUNNING FIXTURE TL-3000. [4] Check the alignment of the INDEXER LEVER with the hole in the TOP PLATE ASSEMBLY at Position 1. [5] Bend the INDEXER LEVER to the correct position. [6] Check the travel of the INDEXER LEVER in the FORWARD position. When the INDEXER LEVER moves in the FORWARD position, the gate edge of the black plastic should be between the 2 holes at Position 2. [7] Bend the INDEXER LEVER until you reach the correct position. Adjustment Specification Use TL-3000 MECHANISM RUNNING FIXTURE. Use TL-3001 to measure the height of the SLIDE LIFT LEVER. The LEVER should make contact with the low surface of TL-3001. The LEVER should not make contact with the high surface of TL-3001. SM4530-1 ­ 30APR96 27 SERVICE MANUAL Adjusting the SLIDE LIFT LEVER MANUAL SLIDE LIFT LEVER GUAGE TL-3001 SLIDE LIFT LEVER SELECT LEVER (not shown) A091_0016BCA A091_0016BA Warning Dangerous Voltage [1] Disconnect the main power. Important The older style MECHANISM SLIDE LIFT LEVER has an ECCENTRIC on it to do this adjustment. [2] Do the removal for the MECHANISM ASSEMBLY. [3] Place the MECHANISM ASSEMBLY on the MECHANISM RUNNING FIXTURE TL-3000. [4] Press and hold the SELECT LEVER down to move the SLIDE LIFT LEVER to the highest position. [5] Measure the height of the SLIDE LIFT LEVER. The SLIDE LIFT LEVER should make contact with the low surface of the SLIDE LIFT LEVER GAUGE TL-3001; the SLIDE LIFT LEVER should not make contact with the high surface of the SLIDE LIFT LEVER GAUGE TL-3001. [6] Bend the SLIDE LIFT LEVER until the adjustment is correct. Adjustment Specification Use TL-3000 MECHANISM RUNNING FIXTURE. Use TL-3001 to measure the height of the SLIDE LIFT LEVER. The LEVER should make contact with the low surface of TL-3001. The LEVER should not make contact with the high surface of TL-3001. 28 30APR96 ­ SM4530-1 Adjustments Adjusting the SLIDE LIFT LEVER POWER SLIDE LIFT LEVER GUAGE TL-3001 SLIDE LIFT LEVER SELECT LEVER (not shown) A091_0016BCA A091_0016BA Warning Dangerous Voltage [1] Disconnect the main power. Important The older style MECHANISM SLIDE LIFT LEVER has an ECCENTRIC on it to do this adjustment. [2] Do the removal for the MECHANISM ASSEMBLY. [3] Place the MECHANISM ASSEMBLY on the MECHANISM RUNNING FIXTURE TL-3000. [5] Press and hold the SELECT LEVER down to move the SLIDE LIFT LEVER to the highest position. [6] Measure the height of the SLIDE LIFT LEVER. [. . . ] Check that the MAIN PROJECTION LAMP operates correctly. Insert the TARGET SLIDE TL-3002 in the GATE MECHANISM. · Check that the TARGET is correctly aligned. Check that the voltages across the PHOTOCELL are correct. [. . . ]