User manual KOMPERNASS LERVIA KH 1150 CEILING FAN WITH HALOGEN LIGHTING

[. . . ] · Do not kink or crush the power cord. · If the power supply wire or the device housing are damaged, you must have the device repaired by an expert before using it again. In this case, the device is not safe and the warranty is voided. Fire hazard · Never leave the appliance unattended whilst in use. [. . . ] This ceiling fan is intended exclusively for use in private households. Observe all information in this installation and operating manual, in particular the safety instructions. Any other use is considered improper use. 3 Product Overview A B C D E F G H I J K L Casing Extension rod (2 variants) Connector Sliding switch for changing the direction Light module with 3 bulbs (incl. 3 halogen light bulbs) Pull chain for the light Pull chain for changing the speed Blades (5 pcs. ) Blade attachment (5 pcs. ) Blade mount (5 pcs. ) Motor housing Installation plate 5 IB_KH1150_E2731_UK_V1. qxd 15. 01. 2007 14:47 Uhr Seite 6 4 Product Description The KH 1150 ceiling fan has three speed levels that are controlled with the pull chain. The direction can be changed with a switch, allowing the fan to blow air downward or draw it up. In addition, the fan is equipped with a light with 3 halogen bulbs; the light is switched on and off with a separate pull chain. 5 Guide Section 6 describes the installation and Section 7 describes the basic operation of the KH 1150 ceiling fan. Read these sections carefully in order to perform the installation quickly and properly and to understand all the functions of the fan. The following signal words and symbols are used: DANGER Warns against possibly serious or fatal injuries WARNING Warns against possible minor injuries or possible material damage CAUTION Warns against possible defects or destruction of the product IMPORTANT / NOTE Provides important or useful information 6 IB_KH1150_E2731_UK_V1. qxd 15. 01. 2007 14:47 Uhr Seite 7 6 Installing the Ceiling Fan WARNING: Follow the safety instructions (see Section 1) to avoid injuries or damage as a result of installation errors. NOTE: The letters in parentheses refer to the figure in Section 3 "Product Overview". Required Tools Phillips head screwdriver Open-jawed spanner 8 mm 6. 1 Installing Blade mounts (J) 1 Select the desired decor: wood grain or white surface. Lay out the blades so that the desired decor faces down. 2 Run the lock pins of a blade mount (J) through the 3 openings of a blade (H) from below. Position the blade attachment (I) and push in the direction of the arrow (see Fig. ). The spring clip must snap in and secure the middle pin (see Fig. : circle). Mount all blades in the same way. H I J 6. 2 Installing the Extension Rod (B) 1a Long rod with plastic mount: Step 1: Loosen the side locking pin on the extension rod (see Fig. : circle). Step 2: Slide the mount downward until the lock pin is exposed. Step 3: Pull out the lock pin. 3 1 2 7 IB_KH1150_E2731_UK_V1. qxd 15. 01. 2007 14:47 Uhr Seite 8 1b If you would like to use the short extension rod, pull the mount entirely off the long rod and slide it about halfway onto the short rod, as shown. 2 Step 1: Loosen the side screws of the connector (C) so that the extension rod can be inserted. Step 2: Remove the pins of the connector: Pull out the linch pin. Step 3: Remove the pin. C 2 31 3 Pull the cable through the casing and place the casing onto the motor housing over the connector. DANGER: Damaged cables lead to shortcircuits. In such cases, touching the fan could be lifethreatening! Do not damage the cable when inserting the pin! 4a Step 1: Long extension rod: Pull the cable through, then insert the extension rod into the connector. Step 2: Install the lock pins of the connector. Step 4: First tighten both screws evenly at the same time until hand-tight, then screw them in tightly with the screwdriver. 4b Short extension rod: After pulling the cable through (see 4a, substep 1), you must first perform the following installation step 5. [. . . ] Check the cable plug Have the fan inspected by an expert or send it to customer service (See the enclosed "Warranty" for the service address) Check the screw connection of the blade mounts Check the blades, replace if necessary Change the positioning of the blades amongst themselves. Check the blade attachments Fan defective Fan runs loadly or sways significantly Blade mounts not firmly connected Blade damaged Blades not balanced out Loose blade attachment(s) Fan is not hung correctly DANGER: Disconnect the fan from the mains network before checking whether it is hung correctly. Check the fastening of the installation plate and extension rod, and correct any improper fastening Check the halogen bulbs and replace defective bulbs Light does not function Bulb defective Loose cable plug DANGER: Disconnect the fan from the mains network before checking the cable plug. Check the cable plug Do not perform any modifications or repairs on the product! [. . . ]