User manual KONICA MINOLTA 7033 EV5

[. . . ] INSTRUCTION MANUAL 7033 INSTRUCTION MANUAL 7033 Before copying, read this guide. Keep in the right hand rear pocket of the machine. Thank you very much for your purchase of the Konica 7033. This Manual deals with making copies, correct handling of the machine, and precautions for safety. In order to maintain a satisfactory copying performance, please keep this Manual readily available for reference in the right hand rear pocket of the machine. ENERGY STAR® Program The ENERGY STAR Program has been established to encourage the widespread and voluntary use of energy-efficient technologies that reduce energy consumption and prevent pollution. [. . . ] 12-5. CAUTION: Paper Capacity of the Finisher The capacity of the Finisher exit tray is listed below. When the total number of copies in the copy run exceeds the stated capacity, be sure to unload the exit tray whilst the copier is still copying. Failure to do so will cause the copier to jam. The following capacity is for 80g/m2 paper. When copying mixed size originals, the capacity will be less than the following. Non-sort mode Tray 1: 100 sheets/ 10 sheets (thin/thick paper, OHP films, etc. ) Tray 2/3: 500 sheets (A4R, A4, B5R, B5, 8. 5"x11"R) 300 sheets (A3, B4, F4/8. 5"x13", A5R) Sort/Group mode Tray 2/3: 500 sheets (A4R, A4, B5R, B5, 8. 5"x11"R) 300 sheets (A3, B4, F4/8. 5"x13") CAUTION: Maximum Loading Capacity of the Exit Tray In the case of the copier without a finisher, the exit tray capacity is 100 sheets. Be sure to remove the copies from the exit tray while copying before the maximum capacity is reached. Failure to do so will cause the copier to jam. · · · To release OHP Interleave mode, display the Application Selection screen, touch "OHP Interleave" key and then touch "OK" key. To release all the application functions, display the Application Selection screen and touch "ALL CLEAR" key. To restore the initial copying conditions, press the AUTO RESET button on the Operation panel. 8 - 32 Section 8 : Special Copying : Page Editing 7. Image Insert Image Insert is used to combine images scanned from the platen glass with images scanned from RADF. Then, output the combined images as a finished set. Place originals onto RADF 78 1 23 45 6 78 34 1 2 5 6 Insertion originals Place originals onto RADF 6 4 2 8 6 3 5 7 5 3 1 1 2 7 4 8 Basic rules for Image Insert · Scan and store originals into memory, then print all the pages collectively. Advice If memory overflow frequently occurs, you are recommended to extend the memory. · Use the RADF store mode to scan first the originals to have insertions. · Use the Platen store mode to scan next the originals to be inserted. · The Store mode is available only when used as above. Image Insert Specifications RADF capacity : 50 max. can be scanned at a time using Store mode. 999 Original paper size : A3, B4, A4R, A4, B5R, B5, A5*, 8. 5"x11"R Tray paper size : A3, B4, A4R, A4, B5R, B5, A5*, 8. 5"x11"R, 8. 5"x11" (80g/m2 paper recommended) Print quantity : 999 sets max. Advice *: Load A5 paper in lengthwise feed ( ) only. OHP Interleave Image Insert 8 - 33 Section 8 : Special Copying : Page Editing 7. Image Insert (continued) Incompatible If any of the following copying conditions are going to be set, the Image Insert copying may be cancelled or the key concerned on the screen may become faint, not allowing setting. [. . . ] will not light after pressing AUTO RESET button. Is the Rotation activated? · Fully close the RADF. · Fully close the RADF. · Set manually on Platen glass, if not. · Correctly load the originals without exceeding the capacity. [. . . ]