User manual KONICA MINOLTA BIZHUB 163

[. . . ] NC-503 User Manual Contents 1 Introduction 1. 1 1. 2 Software end user license agreement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Explanation of manual conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety advices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sequence of action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For the password, consult with the network administrator. 3 Press the [OK] key. After the message "ACCEPTED" appears, the "E-MAIL SETTING 2" menu appears again. 2 Note If a number was incorrectly entered, press the [Clear/Stop] key to erase the number, and then type it in correctly. NC-503 5-43 5 5. 6 LDAP SETTING Network settings Specify the necessary settings in order to use the LDAP (Lightweight Directory Access Protocol) server on the network. LDAP settings are specified from the "ADMIN. This section provides details on specifying settings for the following parameters. - SSL SETTING - SEARCH BASE - ATTRIBUTE - SEARCH METHOD - LDAP TIMEOUT - MAX. SEARCH RESULT - AUTHENTICATION - LDAP ACCOUNT - LDAP PASSWORD - DOMAIN NAME 2 Reminder Before specifying LDAP settings, check with the network administrator for the necessary information. 5-44 NC-503 Network settings Specifying the LDAP server address 5 1 2 Press the [Utility] key in the control panel. Press the [, ] or [+] key until "ADMIN. MANAGEMENT" is selected, and then press the [OK] key. UTILITY MODE USER MANAGEMENT ADMIN. MANAGEMENT COPY SETTING 1 3 Type in the administrator access code, and then press the [OK] key. ­ The manufacturer's default setting is "000000". ADMIN. NO. :------ ­ If the number was incorrectly entered, press the [Clear/Stop] key to erase it, and then type it in correctly. NC-503 5-45 5 4 Network settings Press the [+] or [, ] key until "LDAP SETTING" is selected, and then press the [OK] key. ADMIN. MANAGEMENT LDAP SETTING USER SETTING RETURN ­ If fax kit FK-506 is installed ADMIN. MANAGEMENT E-MAIL SETTING 2 LDAP SETTING COMM. SETTING 5 In the "LDAP SETTING" menu, press the [+] or [, ] key until "LDAP SERVER ADDR. " is selected, and then press the [OK] key. LDAP SETTING LDAP SERVER ADDR. SSL SETTING 5-46 NC-503 Network settings 5 6 Type in the IP address or host name for the LDAP server. LDAP SERVER ADDRESS ­ ­ ­ ­ The host name can contain a maximum of 64 characters. To specify a host name for the LDAP server, the DNS setting must be specified. For the IP address or host name of the LDAP server, consult with the network administrator. If the setting was incorrectly entered, press the [Clear/Stop] key to erase it, and then type it in correctly. 7 Press the [OK] key. After the message "ACCEPTED" appears, the "LDAP SETTING" menu appears again. NC-503 5-47 5 Specifying the LDAP port number Network settings 1 In the "LDAP SETTING" menu, press the [+] or [, ] key until "LDAP PORT NO. " is selected, and then press the [OK] key. LDAP SETTING LDAP SERVER ADDR. SSL SETTING 2 Type in the port number. LDAP PORT NO. ­ A port number between 1 and 65535 can be specified. If SSL is enabled, use port number 636. 3 Press the [OK] key. After the message "ACCEPTED" appears, the "LDAP SETTING" menu appears again. 5-48 NC-503 Network settings Selecting the SSL setting 5 1 In the "LDAP SETTING" menu, press the [+] or [, ] key until "SSL SETTING" is selected, and then press the [OK] key. LDAP SETTING LDAP SERVER ADDR. SSL SETTING 2 Press the [, ] or [+] key until "DISABLE" or "ENABLE" is selected, and then press the [OK] key. SSL SETTING DISABLE ENABLE Whether "DISABLE" or "ENABLE" is selected, the message "ACCEPTED" appears, and then the "LDAP SETTING" menu appears again. NC-503 5-49 5 Specifying the search base Network settings 1 In the "LDAP SETTING" menu, press the [+] or [, ] key until "SEARCH BASE" is selected, and then press the [OK] key. LDAP SETTING SEARCH BASE ATTRIBUTE SEARCH METHOD 2 Specify the database where the LDAP server is searched. SEARCH BASE ­ ­ ­ The search base can contain a maximum of 64 characters. [. . . ] The settings in the Web browser are incorrect. 5-13 In the "Address" box, type the IP address of the specified device. Even though the device can be accessed, certain settings must be specified according to the network configuration in order to establish a connection. For details, contact your network administrator. [. . . ]