User manual KONICA MINOLTA BIZHUB PRO 1600P

[. . . ] User manual bizhub PRO 1600P/2000P/2500P Operating information Copyright Copyright 2006-2008 Océ All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in any form or by any means without written permission from Océ. Océ makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Océ reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revision or changes. Edition 2008-07 US Trademarks Trademarks List of trademarks Xerox, DocuTech, DigiPath and FreeFlow are registered trademarks of Xerox Corporation. [. . . ] This section describes how to change the sorting method for a specific job. Illustration [39] [39] Change the sorting method Change the sorting method 1. Press the 'Jobs' button on the operator panel. In the list of 'Waiting jobs' or 'Scheduled jobs', press the job you want to edit. Press 'Properties'. 80 Chapter 4 Working with the operator panel Change the sorting method Note: You can also press the job 2 times to access the 'Properties' window. This function is comparable to double-clicking with a mouse. 4. Press 'Finishing'. The 'Sort' button shows the currently selected sorting method. 5. Press the 'Sort' button. A drop-down list appears. 6. Press 'OK'. 81 Change the type of offset stacking Change the type of offset stacking Introduction You can use the function 'Offset stacking' to create a visible distinction between sets or jobs in an output location. When 'Offset stacking' is enabled, each set or job will be stacked with an offset compared to the previous set or job. You can set the default type of offset stacking in the workflow profile on the operator panel (see `Work with the workflow profiles' on page 104). The following table describes when you can change the type of offset stacking for specific jobs. [15] [15] Possibility to change the type of offset stacking per job When Then The type of offset stacking is set to 'Sets You can change the type of offset (as in job)' stacking per job via the 'Properties' window in the 'Jobs' view. The type of offset stacking is set to 'Jobs', 'Sets (always)', 'Banners' or 'Off' You cannot change the type of offset stacking per job. The 'Properties' window displays 'As in system'. This section describes the following: The values you can select in the 'Properties' window when 'Sets (as in job)' is set in the workflow profile How to change the type of offset stacking per job via the 'Properties' window. Types of offset stacking in the 'Properties' window When 'Sets (as in job)' is set in the workflow profile, then you can select one of the following types of offset stacking. 82 Chapter 4 Working with the operator panel Change the type of offset stacking [16] [16] Available types of offset stacking in the 'Properties' window When You select 'Off' You select 'Each set' You select 'As in document' Then All the printed sets are sent to the output location in one straight stack. All the printed sets are sent to the output location with an offset between the sets. All the printed sets are sent to the output location as defined in the job ticket. Illustration [40] [40] Change the type of offset stacking Change the type of offset stacking 1. On the operator panel, press the 'Jobs' button. In the list of 'Waiting jobs' or 'Scheduled jobs', press the job you want to edit. Press 'Properties'. Note: You can also press the job 2 times to access the 'Properties' window. This function is comparable to double-clicking with a mouse. 4. Press 'Finishing'. 83 Change the type of offset stacking The 'Offset stacking' button shows the currently selected type of offset stacking. 5. [. . . ] You must define a an application or printer driver, the correct controller automatically corrects the combination of job settings. When you define the job settings on settings in the the operator panel, the operator 'Properties' section panel displays a message that the of the 'Jobs' view on defined combination is not possible. The 'OK' button is disabled. Overview of the possible toner problems when using fiber-rich media [33] Toner problem Several toner pollutions on the sheet Solution Reduce the 'Media quality factor' from 600 to 400 or 200 (see Change the media quality factor on page 117). When the print quality is still not optimal, you can enable the 'Enhanced cleaning mode' (see Enable the enhanced cleaning mode on page 117). [. . . ]