User manual KONICA MINOLTA BIZHUB-500-420 PH2 UMLARGE 1-1-0

[. . . ] 500/420 User manual [Enlarge Display Operations] Introduction Thank you for choosing this machine. The bizhub 500/420 User manual [Enlarge Display Operations] contains details on the operation of the various functions available in the Enlarge Display mode of the bizhub 500/420 and on the various operating precautions. In order to ensure that this machine is used correctly and efficiently, carefully read the Enlarge Display Mode Operations volume of the User manual before using the machine. In addition, read chapter 2 "Installation and Operation Precautions", of the User manual [Copy Operations]. [. . . ] The following procedure describes how to select Finishing settings. 2-32 bizhub 500/420 (Phase 2) Using copy functions 2 To select Finishing settings 1 Touch [Finishing] on the Basic Screen. The Finishing Screen will be displayed. 2 Select the desired settings. ­ To cancel changes to the settings, touch [Cancel]. ­ To cancel a setting, touch the key again to deselect it. ­ If the "Corner Staple", "2 Staple", or "4-hole Punch" setting was selected, touch [Position bizhub 500/420 (Phase 2) 2-33 2 Using copy functions Setting], and then touch the key for the desired position. Touch [Auto] to automatically determine the stapling or hole-punching position according to the orientation of the loaded original. The paper is stapled or holes are punched along the long side of the paper if the original length is 297 mm or less or along the short side of the paper if the original length is more than 297 mm. 3 Touch [OK] in each screen. The Basic Screen will be displayed. 2-34 bizhub 500/420 (Phase 2) Using copy functions 2 2. 9 Specifying Folding settings Various settings are available for folding copies in half before they are fed out. The following Folding settings are available. Setting Half Fold Fold & Staple Description Select this setting to fold copies in half before feeding them out. Select this setting to staple copies at two places along the center, then fold the copies in half before feeding them out. Copies can be folded and stapled only when the Saddle Stitcher SD-502 is installed in the Finisher FS-510. Copies are stapled at the center, then folded in half before being fed out. 2 Note During the Enlarge Display mode, the 1%2 setting and Booklet function are not automatically selected along with Fold & Staple or Half Fold mode, as they are in normal display mode. Further, Booklet cannot be specified in Enlarge Display mode, while the 1%2 setting is available. bizhub 500/420 (Phase 2) 2-35 2 To select a Folding setting Using copy functions 1 Touch [Folding] on the Basic Screen. The Folding Screen will be displayed. 2 Select the desired settings. ­ To cancel changes to the settings, touch [Cancel]. 3 2-36 Touch [OK]. The Basic Screen will be restored. bizhub 500/420 (Phase 2) Using copy functions 2 2. 10 Selecting the Paper settings Specifying the paper size The size of the paper loaded into the bypass tray can be specified. For details on selecting the Paper settings, refer to the User manual [Copy Operations]. The size of the paper loaded into the bypass tray can be selected in any of the following ways. Setting Auto Detect Custom Size Description Select this setting to automatically detect the size of the paper loaded into the 1st tray. A custom paper size can be set so that the paper tray is used specifically with the selected paper size. In order to specify a custom paper size in Enlarge Display mode, the custom paper size must first be stored before entering Enlarge Display mode. For details, refer to the User manual [Copy Operations]. The following procedure describes how to specify the size of the paper loaded into the bypass tray. bizhub 500/420 (Phase 2) 2-37 2 To specify a paper size Using copy functions 1 Touch [Paper] on the Basic Screen. The Paper Screen will be displayed. 2 Touch [Bypass]. ­ To change the paper size settings for a paper tray other than the bypass tray, refer to the User manual [Copy Operations]. 2-38 bizhub 500/420 (Phase 2) Using copy functions 2 3 Touch [Paper Size]. 4 Touch either [Auto Detect] or [Custom Size]. bizhub 500/420 (Phase 2) 2-39 2 Using copy functions Touching [Custom Size] will display the Custom Size Screen. ­ On this screen, you can select up to 5 custom sizes previously registered. Touch [Custom 1], [Custom 2], or [Custom 3], then touch the desired key. 5 Touch [OK], and then touch [OK] in the next two screens that appear. The Basic Screen will be restored. 2-40 bizhub 500/420 (Phase 2) Using copy functions 2 To select a Paper Type setting If a setting for special paper, such as overhead projector transparencies and other special paper, is selected for a paper tray, that tray is not selected automatically with the "Auto Paper Select" setting or the automatic paper-tray-switching feature. There are limits on the types of paper that can be loaded in a paper tray. For details on the types of paper that can be loaded, refer to the User manual [Copy Operations]. If overhead projector transparencies or thick paper is loaded into the paper tray, be sure to select the corresponding paper type, otherwise a paper misfeed may occur. bizhub 500/420 (Phase 2) 2-41 2 Using copy functions The following procedure describes how to specify the setting for special paper loaded into the bypass tray. 1 Touch [Paper] on the Basic Screen. The Paper Screen will be displayed. 2 Touch [Bypass]. ­ To change the paper size settings for a paper tray other than the bypass tray, refer to the User manual [Copy Operations]. 2-42 bizhub 500/420 (Phase 2) Using copy functions 2 3 Touch [Paper Type]. 4 Select the setting for a special paper type. Touch the key for the desired paper type. bizhub 500/420 (Phase 2) 2-43 2 Using copy functions ­ To cancel changes to the settings, touch [Cancel]. 5 Touch [OK], in each screen. [. . . ] For an account name and password, contact the machine's administrator. If "Account Track Input Method" in Administrator mode was set to "Password Only", log on is possible by only entering the password. For details, refer to the User manual [Copy Operations]. 1 Touch [Account Name]. 5-8 bizhub 500/420 (Phase 2) Additional copy operations 5 ­ The screen that appears differs depending on the Administrator mode settings that have been specified. 2 Using the keyboard that appeared or the keypad on the control panel, type in the account name, and then touch [OK]. ­ Touch [Symbol] or [Shift] to change the characters that are displayed. ­ To change a character in the entered text, touch [ ] and [ ] to move the cursor to the character to be changed, touch [Delete], and then type in the desired letter or number. [. . . ]