User manual KONICA MINOLTA BIZHUB-500-420 UM SCANNER 1-1-0

[. . . ] Contents 1 Introduction 1. 1 1. 2 Trademarks and Registered Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 OpenSSL Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 Structure of the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To clear all values, press the [C] (clear) key. ­ ­ ­ 4-48 bizhub 500/420 Specifying Settings From the Control Panel 4 4 Touch [OK]. IP filtering is set. 2 Note To cancel changes to the setting, touch [Cancel]. bizhub 500/420 4-49 4 RAW Port No. Specifying Settings From the Control Panel Specify the RAW port numbers used by the printer. By specifying multiple port numbers, multiple data can be accepted simultaneously. 1 2 In TCP/IP Setting screen 2/3, touch [RAW Port No. ]. Touch the button for the desired port. 3 4 Touch [ON] or [OFF]. To use the selected port, press the [C] (clear) key to erase the value, and then use the keypad to type in the RAW port number (between 1 and 65535). ­ If a value outside of the allowable range is specified, the message "Input Error" appears. Type in a value within the allowable range. 5 Touch [OK]. The RAW port usage and RAW port numbers are set. 2 Note When using the RAW port, set [Spool Print Job in HDD before RIP] to [ON]. A timeout may occur if it is set to [OFF]. For details on the spool settings, refer to the IC-204 User manual. If the port number is set to an inappropriate value, there may be interference in the network. Do not change the port number unless specifically requested by the network administrator. 4-50 bizhub 500/420 Specifying Settings From the Control Panel 4 4. 10 NetWare Settings The settings for using the machine on a NetWare network can be specified. NetWare Parameters The NetWare settings are as follows: NetWare Setting screen 1/4 Item NetWare Setting Ethernet Frame Type Operating Mode Status Description Specify whether to turn ON the NetWare print settings. Sets the frame type that is used for communications. For details on specifying the settings, refer to "Status" on page 4-55. 2 Note The IPX protocol is not disabled even if NetWare setting is set to [OFF]. NetWare Setting screen 2/4 Item Print Server Name Description Sets the printer server name. Use the keyboard that appears in the touch panel to type in the server name (up to 63 characters). Sets the password that is required when the print server logs in to the file server. Use the keyboard that appears in the touch panel to type in the password (up to 63 characters). Sets the interval (in seconds) for searching the print queue. To change the interval, press the [C] (clear) key, and then use the keypad to type in the value (between 1 and 65535). If "NDS" is selected, bindery is disabled. If "NDS & Bindery" is selected, both NDS and bindery are enabled. Print Server Password Polling Interval NDS/Bindery Setting bizhub 500/420 4-51 4 NetWare Setting screen 3/4 Item File Server Name Specifying Settings From the Control Panel Description Sets the file server name to which the print server logs in. [. . . ] Displays the ability to reproduce the details of images and print matter correctly A function that allows you to view an image before processing a print or scan job Attribute information When using a printer driver, various functions can be specified in the file properties. In the file properties, you can check the attribute information of the file. The rules that allow computers to communicate with other computers or peripheral devices With the scanning operation of the scanner, an image is read while the row of image sensors is gradually moved. The direction that the image sensors are moved is called the main scanning direction, and the direction in which the image sensors are arranged is called the sub-scanning direction. [. . . ]