User manual KONICA MINOLTA BIZHUB 600 UM SCANNER 1-0-0

[. . . ] User's Guide [Network Scanner Operations] Introduction Introduction Thank you for choosing this machine. This manual contains details on the operation of the various functions of the machine, precautions on its use, and basic troubleshooting procedures. In order to ensure that this machine is used correctly and efficiently, carefully read this manual before using the machine. After reading the manual, store it in the designated holder so that it can easily be referred to when questions or problems arise during operation. [. . . ] The LDAP server registration and authentication are set. 2 Note To cancel changes to the setting, touch [Cancel]. 2 Reminder To apply network setting changes, turn off the main power of the machine, wait 10 seconds, and then turn the machine on again. If the LDAP server settings are not specified correctly, network failure may occur. The server administrator should specify LDAP settings. 3-66 bizhub 750/600 Specifying Settings From the Control Panel General Settings 3 The authentication method used when logging on to the LDAP server can be specified. The available authentication methods are as follows: Item [anonymous] [Simple] [Digest-MD5] Description An authentication method that does not require the user name and password A simple authentication method that requires the user name and password An authentication method that can be used on a typical LDAP server. If authentication fails using Digest-MD5, the authentication is performed by automatically switching to CRAM-MD5. An authentication method that can be used with Active Directory in Windows (Kerberos authentication) [GSS-SPNEGO] To specify the authentication method % In the LDAP Server Setting screen, select a setting under "General Settings". 2 Note Set the authentication method to match that used on the LDAP server. Refer to the LDAP server manual for more details. If the authentication method is set to "GSS-SPNEGO", enter the domain name of Active Directory. If "Dynamic Authentication" is set to "Enable", "anonymous" cannot be selected as the authentication method. ! Detail Depending on the authentication method, settings for the following parameters must be set correctly on Setting Up LDAP screen 3/4 in order to perform the "Check Connection" operation. With "Simple" and "DIGEST_MD5/CRAM_MD5": "Login Name" With "GSS-SPNEGO": "Login Name" and "Domain Name" bizhub 750/600 3-67 Specifying Settings From the Control Panel Chapter 3 3 3. 17 Specifying Settings From the Control Panel E-Mail TX (SMTP) Settings Information, such as the SMTP server, that is required to send data as an email attachment in Scan mode can be specified. In addition, authentication settings for logging on to the STMP server can be specified. E-Mail TX (SMTP) Parameters The E-Mail TX (SMTP) parameters are as follows: E-Mail TX (SMTP) screen 1/2 Chapter 3 Item E-Mail TX Setting SMTP Server Address Description Sets whether to turn on the e-mail transmission. The SMTP server address used to send e-mail can be specified. For details on specifying the settings, refer to "SMTP Server Address" on page 3-71. Sets whether to divide the large-sized data into smallersized ones and transfer them. This setting is used in an environment where the capacity per e-mail is limited by the mail server and when you want to transfer the data exceeding the limited capacity. Sets the divided data size when dividing the data to be sent. To change the value, press the [C] (clear) key, and then use the keypad to type in the value (between 100 and 15000 kb). Specifying Settings From the Control Panel Binary Division Divided Mail Size ! Detail When any virus scan software is used on the mail server, the function of "Binary Division" may not be used. For details, consult your network administrator. To receive the binary divided data via e-mail, it is necessary to use e-mail client software which supports the reception of the binary divided data. Note that the binary divided data you received cannot be combined in some e-mail client software. SMTP Detail screen Item Port No. Description Set the port number used to communicate with the SMTP server. [. . . ] 1-4, 2-18 Sending data via e-mail . . . . . . . . . . . 1-3, 2-6 Sending data via network (SMB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5, 2-30 Separate scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-68 Simplex/duplex setting . . . . . . . . . . . . . . . . . . [. . . ]