User manual KONICA MINOLTA BIZHUB-750-600 PH2 UMLARGE 1-1-0

[. . . ] 750/600 User manual [Enlarge Display Operations] Introduction Thank you for choosing this machine. The bizhub 750/600 User manual [Enlarge Display Operations] contains details on the operation of the various functions available in the Enlarge Display mode of the bizhub 750/600 and on the various operating precautions. In order to ensure that this machine is used correctly and efficiently, carefully read the Enlarge Display Mode Operations volume of the user manual before using the machine. After reading the Enlarge Display Mode Operations volume of the user manual, store it in the designated holder so that it can easily be referred to when questions or problems arise during operation. [. . . ] ­ To select "Letterhead", "Special paper", "Tab Paper", "Recycled", "Fine", "Labels" or "Colored Paper", touch [Paper Type 2]. 5 Touch [OK], and then touch [OK] in the next screen that appears. The Basic screen appears again. 2-40 bizhub 750/600 (Phase 2) Using copy functions 2 2. 11 Scanning the next original during printing (reserving a copy job) The settings for the next copy job can be specified and the original can be scanned while a copy operation is being performed so that it can be printed once the current copy operation is finished. ! Detail Up to 61 copy jobs, including the current copy job, can be reserved. A copy job can be reserved after scanning of the positioned original is finished. The next job cannot be reserved while a original is being scanned. bizhub 750/600 (Phase 2) 2-41 2 To reserve a copy job Using copy functions 1 Press the [Start] key to begin scanning and printing the current copy job. A message appears, indicating that the original is being scanned. 2-42 bizhub 750/600 (Phase 2) Using copy functions 2 2 When the message "Ready to accept another job. " appears, copy settings can be specified for the next copy job. ­ For details on positioning the original, refer to "Feeding the original" on page 1-16. 3 4 Press the [Start] key. After the current copy job is finished, the next copy job begins. When the current copy job is finished, the copy settings for the next copy job are automatically displayed and the copy operation begins. bizhub 750/600 (Phase 2) 2-43 2 Using copy functions 2. 12 Stopping scanning/printing The following procedure describes how to stop scanning the original and stop the printing operation. To stop scanning/printing 1 Press the [Stop] key while a original is being scanned or a job is being printed. A screen appears, allowing scanning/printing to be stopped. If a original is being scanned for a job, pressing the [Stop] key stops scanning. 2 2-44 To continue all stopped jobs, press the [Start] key. bizhub 750/600 (Phase 2) Using copy functions 2 ! Detail To delete the stopped job, touch [Delete]. Select the job to be deleted, and then touch [Delete]. Select only one job at a time to be deleted. bizhub 750/600 (Phase 2) 2-45 2 Using copy functions 2-46 bizhub 750/600 (Phase 2) 3 Using scan functions Using scan functions 3 3 3. 1 2 Using scan functions General scan operation Note For details on the scan operation, refer to the User manual [Network Scanner Operations]. ! Detail Specify the scan settings and network settings and register destinations before entering Enlarge Display mode. For details, refer to the User manual [Network Scanner Operations]. This section contains information on the general operation for scanning. bizhub 750/600 (Phase 2) 3-3 3 To perform a scanning operation Using scan functions 1 2 3 Press the [Scan] key in the control panel, and then press the [Enlarge Display] key. The Scan mode screen appears in Enlarge Display mode. ­ For details on positioning the original, refer to "Feeding the original" on page 1-16. Specify the recipient. ­ For details on specifying recipients, refer to page 3-6. 4 3-4 Specify the necessary scanning settings. ­ For details on specifying scanning settings, refer to page 3-15. bizhub 750/600 (Phase 2) Using scan functions 3 5 Press the [Start] key. Pressing the [Stop] key during scanning, temporarily stops the scanning operation. bizhub 750/600 (Phase 2) 3-5 3 Using scan functions 3. 2 ! Specifying a recipient Detail Destinations must first be registered in Utility mode. For details on registering destinations, refer to the User manual [Network Scanner Operations]. The scan data can be sent in any of the following ways. Operation Scan to E-Mail Scan to FTP Description The scan data can be sent as an attached file to the specified e-mail address. A network environment that includes an FTP server can be used. The scan data is sent to a folder specified on the FTP server on the network. This is suitable for transmitting large-sized data, such as high-resolution data. [. . . ] If "Account Track Input Method" in Administrator mode was set to "Password Only", log on is possible by only entering the password. For details, refer to the User manual [Copy Operations]. 1 Touch [Account Name]. 5-8 bizhub 750/600 (Phase 2) Additional copy operations 5 ­ The screen that appears differs depending on the Administrator mode settings that have been specified. 2 Using the keyboard that appeared or the keypad in the control panel, type in the account name, and then touch [OK]. ­ Touch [Symbol] or [Shift] to change the characters that are displayed. ­ To change a character in the entered text, touch [ ] and [ ] to move the cursor to the character to be changed, touch [Delete], and then type in the desired letter or number. ­ To clear all entered text, press the [C] (clear) key. [. . . ]