User manual KONICA MINOLTA BIZHUB-PRO-1050P-1050EP UM 1-1-0

[. . . ] 1050P/1050eP User Manual Table of Contents 1 Safety Information 1. 1 1. 1. 1 1. 1. 2 1. 2 1. 2. 1 1. 2. 2 1. 2. 3 1. 2. 4 1. 2. 5 1. 2. 6 1. 3 1. 4 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Warning and Precaution Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Meaning of Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Regulation Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select whether or not to print the standard-sized original having tab part image printed on the right edge properly onto tabbed print paper by shifting the scanned image 12. 5 mm to the right side. 12-18 bizhub PRO 1050P/1050eP User Setting Procedure 12 Touch [02 Function Setting] - [02 Each Function Setting]. Touch [Decimal On] or [Decimal Off] to specify image shift in decimal point or not. Select the desired interval time key of the right side of [Printer Prohibit Timer] to set the timer. Touch [On] or [Off] for each of Needless Tab Paper Exit and Auto Image Shift (Tab Print) to specify whether or not to use those functions. 1 2 3 Touch [OK] to complete the setting and return to the Utility Menu Screen. ! Details The Needless Tab Paper Exit key may not be displayed depending on the finisher type mounted on the machine. bizhub PRO 1050P/1050eP 12-19 12 12. 2. 4 03 Tandem Setting User Setting The following settings are provided for the tandem output mode, which is specified on the master machine and used to distribute plural number of print quantity among two machines (master and tandem). 01 Tandem Machine One Time Data Read: On/Off Select [Off] so that both master and tandem machines start printing at the same time, while the master machine continues scanning the image data. Select [On] so that the tandem machine will be kept waiting till it receives all the image data transmitted from the master machine, while the master machine already started to print. 02 Tandem Machine Wait/Proof: Permit/Prohibit Select [Prohibit] so that the master machine starts proofprinting without transmitting the image data to the tandem machine. In this case, the tandem machine receives the data and starts printing when normal printing job has been started. Select [Permit] so that the master machine transmits the scanned image data to the tandem machine and both machines start proofprinting at the same time. 03 Tandem Machine Shift Data Setting: Master Machine Shift data/Tandem Machine Shift data Select [Master Machine Shift data] so that the tandem machine uses the same shift value used on the master machine. Select [Tandem Machine Shift data] so that the tandem machine independently uses the shift value specified on it. If [Prohibit] is selected in [02 Tandem Machine Wait/Proof], the shift value specified on the tandem machine cannot be used because the master machine transmits the scanned image data which already reflect its shift value. 12-20 bizhub PRO 1050P/1050eP User Setting 12 bizhub PRO 1050P/1050eP 12-21 12 User Setting Procedure 1 2 Touch [02 Function Setting] - [05 Tandem Setting]. Touch the item key (from 01 to 04) and make a selection for each. Touch [01 Tandem Machine One Time Data Read], select [On] or [Off], then touch [OK]. Touch [02 Tandem Machine Wait/Proof], select [Permit] or [Prohibit], then touch [OK]. Touch [03 Tandem Machine Shift Data Setting], select [Master Machine Shift data] or [Tandem Machine Shift data], then touch [OK]. 3 Touch [Return] to restore the Utility Menu Screen. 12-22 bizhub PRO 1050P/1050eP User Setting 12 12. 2. 5 03 Touch Screen Adjustment Use this function to check the touch screen and realign the position of the touch sensor that may have shifted. ! Details The Touch Screen Adjustment Screen can be displayed on the Utility Menu Screen by pressing [3] of the control panel keypad. Service can set the machine to forbid users to access this function from the menu and to display the Touch Screen Adjustment Screen only when pressing [3] with the Utility Menu Screen displayed. Contact your service representative for details. Procedure 1 2 3 4 Touch [03 Touch Screen Adjustment]. Touch the "+" symbol at the upper right corner, then lower left corner on the screen. The present coordinates will be displayed in the message area of the screen. Check that the × coordinate and Y coordinate displayed in the first line of the message area fall within the standard value displayed in the second line. Touch each [Check Button] at the upper left and lower right corners on the screen to check if the buzzer tone functions normally. bizhub PRO 1050P/1050eP 12-23 12 5 6 User Setting If the coordinates fall out of the range of the standard value in step 3, or the buzzer tone does not sound in step 4, repeat the adjustment procedure from steps 2 to 4 or contact your service representative. [. . . ] 12-20 Tandem Machine Wait/Proof 12-20 Tandem mode . . . . . . . . . . . . . . . . . . . . . . . . 6-24 Tandem Setting . . . . . . . . . . . . . . . . . . . . 12-20 TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-65 TIFF Setting . . . . . . 10-6, 10-9, 10-14 Time and Date Setting . . . . . . . . . . . 13-8 Timer Action On/Off Setting . 13-17 Timer Interrupt . . . . . . . . . . . . . . . . . . . . . . . 2-30 Timer Interrupt password . . . . . . . 2-31 Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]