User manual KONICA MINOLTA CROWNNET Setup Guide

[. . . ] QMS® CrownNet® Setup Guide 1800329-001H Trademarks The following are trademarks or registered trademarks of their respective owners. Other product names mentioned in this manual may also be trademarks or registered trademarks of their respective owners. Registered trademarks are registered in the United States Patent and Trademark Office; some trademarks may also be registered in other countries. QMS, Crown, CrownNet, the QMS logo, and the Crown seal are registered trademarks of QMS, Inc. [. . . ] Skip to "Network Configuration" on page 39. 6 36 QMS CrownNet Setup Guide Interface Configuration NetWare Interface Configuration (Netware 4. x) Unless you want to use the default settings, use the following procedure to name the file and print servers. » Note: In CrownAdmin 3, the printer shows up as QMS-xxxx-PrintSystem-hardwareaddress, where xxxx is the printer model number and hardwareaddress is the printer's hardware address as found on the printer start-up page. 1 In the Administration/Communications/xxxxxxxx NIC/CrownNet/NetWare/Config PServer/PServer Context[1], PServer Context[2], and PServer Context[3] menus (where xxxxxxxx is either Resident or Optional), enter the name of the configuration file server and print server context. Note: The three PServer Context[x] menus allow you to identify the name of the NDS configuration file server and the print server context. The format for the option is n n n File server name Space Print server context » For example, if the configuration file server name is QMS-4 and the print server context is PRINTSERV2. SALES. QMS, you would enter: QMS-4 PRINTSERV2. SALES. QMS » Note: Make sure to put a space between the file server name (QMS-4) and the print server context (PRINTSERV2. SALES. QMS). Up to 16 characters can be entered in the Pserver Context[1] field, and additional 16 characters in Pserver Context[2] field, and 15 characters in the Pserver Context[3] field. » Note: If you need to assign more than 14 characters to the file server name you must use CrownAdmin 3 to enter the name. QMS CrownNet Setup Guide 37 Interface Configuration 2 Reset the CrownNet interface by using the Administration/ Communications/xxxxxxxx NIC/CrownNet/Common/Soft Reset menu (where xxxxxxxx is either Resident or Optional). Skip to "Network Configuration" on page 39. 3 TCP/IP Interface Configuration 1 If necessary, in the Administration/Communications/ xxxxxxxx NIC/CrownNet/TCPIP/Internet Address menu (where xxxxxxxx is either Resident or Optional), enter the printer's Internet address. The factory default Internet address is 161. 033. 128. 024. 2 If necessary, in the Administration/Communications/ xxxxxxxx NIC/CrownNet/TCPIP/Default Router menu (where xxxxxxxx is either Resident or Optional), enter the Internet address of the default router. The factory default router address is 000. 000. 000. 000. 3 If necessary, in the Administration/Communications/ xxxxxxxx NIC/CrownNet/TCPIP/Subnet Mask menu (where xxxxxxxx is either Resident or Optional), enter the printer's subnet mask. The default subnet mask is 000. 000. 000. 000. This setting provides automatic sensing of gateways. If you identify a subnet mask, automatic sensing is disabled. 4 Go to "Network Configuration" on page 39. 38 QMS CrownNet Setup Guide Network Configuration Network Configuration CrownNet Print Utility for Windows Configuration Follow the appropriate procedure below to install a QMS CrownNet printer port as a Windows port and to connect it to a printer driver. The procedure you use depends on the version of Windows you're running. » Note: You must have the QMS CrownNet Print Utility software installed before completing these procedures. Windows 3. 1 and Windows for Workgroups 3. 11 » Note: Windows 3. 1 requires OS/2 LAN Server/LAN Manager Workstation Service. Windows for Workgroups 3. 11 requires Microsoft Windows Network (Microsoft NetBEUI protocol). Refer to your Windows documentation for installation instructions. 1 2 3 Double-click the CrownNet Print Utility icon to start the utility. In the CrownNet Port list, select the CrownNet port you want to install. [. . . ] Is the printer connected to the network?Is the printer plugged in, turned on, and correctly configured?Do the printer start-up and status pages list the interface?Is the configuration information correct? [. . . ]