User manual KONICA MINOLTA DYNAX 7000

[. . . ] A NEW DIGITAL MAGNIFICATION FUNCTION After extending the optical zoom (telephoto) to 115mm, release the right button and then press it again to select digital magnification. Press the right button once to increase the magnification of the live image on the LCD monitor. The full size (2. 0X) image is 672 pixels (horizontal) x 504 pixels (vertical) (1/4 size (2. 2X) image of 288 pixels (horizontal) x 216 pixels (vertical)). [. . . ] Press the left button once to decrease the digital magnification of the image. After decreasing magnification to the minimum size image of 1344 pixels (horizontal) x 1008 pixels (vertical) (1/4 size image of 640 pixels (horizontal) x 480 pixels (vertical)), press the left button once to re-select the optical zoom (telephoto). appears at the top-right of the REC screen when digital magnification is Trimmed area (displayed area) with digital magnification Full size Width (pixels) 1344 1120 1024 960 896 768 672 Height (pixels) 1008 840 768 720 672 576 504 Width (pixels) 640 576 512 448 384 320 288 1/4 size Height (pixels) 480 432 384 336 288 240 216 Magnification for digitally magnified area. 1. 0X (1. 0X) 1. 2X (1. 1X) 1. 3X (1. 3X) 1. 4X (1. 4X) 1. 5X (1. 7X) 1. 8X (2. 0X) 2. 0X (2. 2X) · The digital magnification function operates only when the LCD monitor is switched ON. When digital magnification has been selected it is cleared by pressing the LCD monitor ON/OFF button on the lens unit to switch the monitor OFF. · Digital magnification cannot be used when the wide-angle 1500 lens unit is fitted. · When the PLAY or REVIEW mode is selected while digital magnification is selected, selecting the REC mode again clears digital magnification. · Motion in digitally magnified live images is slightly jerky with digital magnification selected, however this has no effect on image quality. · Images recorded from the digitally magnified area are trimmed in the vertical and horizontal directions as shown above (they are not reconstructed to 1344x1008 pixels), and appear as smaller images when displayed on the PC monitor screen or when printed. 3 2. Press the End soft key to return to the initial (live image) screen. · A custom white balance once set is maintained until another white balance is selected, or the camera power supply is switched OFF. Switching the camera power supply OFF clears the custom white balance. 6 7. IMPROVED CUSTOM SCRIPT FUNCTION (see User's Manual P102) A script prepared by the user is run as described below. Shutter Speed Setting The manual exposure mode is selected from the menu and the desired shutter speed is set (the f-stop cannot be changed) using a script. Shutter speed can be set up to 2 seconds at maximum. Changing ISO Sensitivity Automatic gain control operates to amplify the signal when the subject is dark and the signal level is low. Note that gain is normally fixed However, it may be altered with the script. Please note that the noise in the signal may increase as the gain is increased. Flash Compensation The flash illumination may be controlled for exposure compensation using a script. This compensation differs from the exposure compensation in which the brightness of the whole image is increased. The areas of the image not illuminated by the flash remain unchanged, only the exposure for the subject illuminated by the flash is compensated. Selectable Metering In addition to the normal 25-segment Metering, Center Weighted Average Metering and Spot Metering may be selected with the script to suit the application or purpose. AE Lock Selectable A script may be used to select whether lightly pressing the shutter button is to lock or not lock (focus lock only) AE. Manual White Balance Adjustment White balance may be manually adjusted for red, blue, and green using a script. [. . . ] This compensation differs from the exposure compensation in which the brightness of the whole image is increased. The areas of the image not illuminated by the flash remain unchanged, only the exposure for the subject illuminated by the flash is compensated. Selectable Metering In addition to the normal 25-segment Metering, Center Weighted Average Metering and Spot Metering may be selected with the script to suit the application or purpose. AE Lock Selectable A script may be used to select whether lightly pressing the shutter button is to lock or not lock (focus lock only) AE. Manual White Balance Adjustment White balance may be manually adjusted for red, blue, and green using a script. This function allows fine setting of white balance as necessary to suit photographic requirements. Manual Focus Focus may be adjusted with the cross-hairs keys (right and left) using a script. [. . . ]