User manual KONICA MINOLTA EP2080

[. . . ] i EP2080 Thank you for choosing Minolta. This operator's manual explains how to operate the copier and replenish its supplies. It also gives some troubleshooting tips as well as general precautions to be observed when operating the copier. To ensure the best performance and effective use of your copier, read this manual carefully until yo u familiarize yourself thoroughly with its operation and features. [. . . ] Job Memory Input and Job Recall The job settings appear on the Touch Panel. 6 After you have checked the settings, touch Exit . 7 Touch Exit on the Job Memory Input screen. Then, the Basic screen reappears. Using the User Mode Chapter 4 80 1. Job Memory Input and Job Recall Deleting a Program 1 Press the User Mode key. Job Recall 4 Touch Exit . Then, the Basic screen reappears. 1134P365CA 2 Touch Job Memory Input . Chapter 4 Touch Account Job if you want to delete a job in Account Job memory. Using the User Mode 3 Touch Delete , then touch the job number key from which you want to delete a job program. The number key you touch should not be marked with . When appears in that key, it indicates that the job program has been deleted. 81 1. Job Memory Input and Job Recall Recalling a Job from Memory 1 Press the Job Recall key. Job Recall 1134P365CA 2 Touch the number key in which the desired job has been stored. 3 Check the settings made and then touch Exit . The copier is set up for these settings and the Basic screen reappears. If the job recalled is not what you want, touch Cancel . Then, the Job Recall screen reappears. Using the User Mode If you want to recall a job from Account Job memory, touch Account Job and then the number key. Chapter 4 82 2. Zoom Memory Input Up to two different, frequently used zoom ratios can be stored in memory so you can use them later whenever necessary. For the Minimal ratio, X0. 930 has been factory-set, but that can be changed as necessary. Storing a Zoom Ratio 1 Press the User Mode Key. User Mode 4 Touch the desired number key in which you want to store the zoom ratio, either 1 or 2 . 1134P356CA 2 Chapter 4 Touch Zoom Memory Input . NOTES · When a new zoom ratio is stored in a Using the User Mode 3 Using the 10-Key Pad, enter the desired zoom ratio. key number, the old one stored in that key number is lost. · The custom zoom ratios may also be stored using the screen accessed by the User Set key which is shown when Zoom is touched on the Basic screen. The Basic screen reappears. For example, enter X1. 234, as 1 , 2 , 3 , and 4 , in that order. To correct an entry, press the Clear key, then enter the new ratio. NOTES · The zoom ratio can range from ×0. 500 · The Minimal ratio can range between to ×2. 000. ×0. 900 and ×0. 999. 83 3. Meter Count, Toner Replenisher, and Drum Dehumidifier Meter Count Touching [Meter Count] allows you to check the total count of each of the following five counters. Total Counter Shows the total number of copies made since the installation of the copier. 2-Sided Total Shows the number of 2-sided copies. 2-Sided Size Shows the number of copies made on copy paper of a preset size (the same size as set for Size Counter). Size Counter Shows the number of copies made on copy paper of a preset size. (The size will be set by your Technical Representative. ) # of Active Accounts Shows the total number of copies made by the active accounts. Chapter 4 Toner Replenisher Touching [Toner Replenisher] sets the copier into the auxiliary toner replenishing mode. The copier tends to exhaust the supply of toner rapidly when making a number of copies from an original with dark solid areas such as a photo. As a result, the image density of the copy will become lighter. In such a case, you can use Toner Replenisher to regain the normal image density quickly. NOTES · Do not turn OFF the Power Switch or open the Front Door while the copier is replenishing toner. · Toner is not replenished if the image density is sufficiently high. · The toner replenishing sequence ends automatically. Drum Dehumidifier Touch [Drum Dehumidifier] to activate the Drum Dehumidifier function. During times of high humidity or when there are sudden rapid changes in humidity (especially when you are using a heater in winter), condensation*1 can form on the surface of the PC Drum*2, resulting in blotchy copies. [. . . ] 21 Auto Drawer Switching p . 35 Auto Dual Function p. 21 Auto Panel Reset (User's Choice) p. 86 Auto Paper p. 16 Confirmation Beep (User's Choice) p. 16 Copy Mode Priority (User's Choice) p. [. . . ]