User manual KONICA MINOLTA IC-202 PH2 UM 1-1-0

[. . . ] The essentials of imaging IC-202 Contents 1 Introduction OpenSSL Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 1. 1 1. 2 Software license agreement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 About this user manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ­ Up to 30 settings can be added to one list. IC-202 (Phase 2) 6-31 6 6. 4 Setting up the PCL driver Specifying the special functions tab settings 6-32 IC-202 (Phase 2) Setting up the PCL driver Image on two pages is printed on a sheet of paper of double size (combination) 6 Contents of two sheets of output size can be collected and printed on one sheet of paper of twice the size as set in "Output size". 1 2 3 Click Special Functions tab. Select the "Combination" check box. Click [, ] next to the "Combination" check box and select "2 in 1" or "2 Repeat" from the list displayed. If you select "2 in 1", image on continuous 2 pages is collected and printed on one sheet of paper. If you select "2 Repeat", two sheets of the same pages are printed on a sheet of paper. IC-202 (Phase 2) 6-33 6 Setting the fold Setting up the PCL driver Paper is folded and output. You can select Half Fold, Z Fold or Tri-Fold. 1 2 3 Click the Special Functions tab. Click [, ] next to the "Fold" check box. Select "Half Fold", "Z Fold" or "Tri-Fold" from the list displayed. 2 Note Some items may not be displayed depending on the finisher installed. 6-34 IC-202 (Phase 2) Setting up the PCL driver Adjusting the printing position (image shift) You can adjust the printing position on the output paper. 6 1 2 3 4 Click the Special Functions tab. Select the "Image Shift" check box. Set the up/down/left/right shift on the front and back sides or shift of paper interval in the unit of 0. 1mm. 2 Note The "Switch Setup" function does not work. Only a setup from Printer Driver side is possible. By selecting the "Back Side Auto Setup" check box, the setting becomes the same as that on the front side. IC-202 (Phase 2) 6-35 6 6. 5 Specifying the overlay tab settings Setting up the PCL driver Printing different original documents together (overlay) An original document can be printed on top of overlay data that was created separately. This function is handy for fax cover letters and form letters. You must pre-register forms to be printed. For details, refer to "Creating overlay" on page 6-38. 1 2 3 4 5 Create the print data using any application. From the "File" menu, select "Print". Select the KONICA MINOLTA 750/600 PCL printer, and then click [Preferences]. Select "Print Overlay". 6-36 IC-202 (Phase 2) Setting up the PCL driver 6 6 From the list, select the overlay that you want to print. ­ When the 1st page only is printed in overlay, turn on the "1st Page Only" check box. 7 8 Select the file name, and then click [OK]. ­ The Print dialog box appears again. Click [OK]. Overlay printing is performed. IC-202 (Phase 2) 6-37 6 Creating overlay Setting up the PCL driver To use overlay, the data for using overlay must be pre-registered. To register a overlay, select the "Create Overlay" check box, and then specify the document that you want to register. 1 2 3 4 5 Create the overlay data using any application. From the "File" menu, select "Print". Select the KONICA MINOLTA 750/600 PCL printer, and then click [Preferences]. [. . . ] Monochrome image expressive form using the gradation information from black to white. Hardware and software used as the point where a network is connected to a network. A gateway also changes data formats, addresses, and protocols according to the connected network. The unit used to divide a TCP/IP network into small networks (subnetworks). [. . . ]