User manual KONICA MINOLTA IC-402

[. . . ] Image Controller IC-402 User's Guide [Network Scanner Operations] [Copier Network Functions] Introduction Introduction Thank you for choosing this machine. This User's Guide contains descriptions of the network scanning functions and operations that can be used from optional C450/C351 image controller IC-402 and the network functions that can be used from the copier when the IC-402 is installed. To ensure the best possible performance and most effective use of the machine, read this manual thoroughly. After reading this User's Guide, store it in the designated holder for quick reference when problems or questions arise during operation. [. . . ] When referral is used, the search base that was specified in LDAP Sever Setting searches the top and bottom levels as the starting point. Use Referral Setting Up LDAP screen 6/6 Item Login Name Description Sets the login name used to connect to the LDAP server. Use the keyboard that appears in the touch panel to type in the name (up to 255 characters). Sets the password used to connect to the LDAP server. Use the keyboard that appears in the touch panel to type in the password (up to 128 characters). Sets the domain name used to connect to the LDAP server as necessary. Use the keyboard that appears in the touch panel to type in the name (up to 64 characters). Password Chapter 6 Domain Name Copier Network Functions 6-12 IC-402 Copier Network Functions To specify Setting Up LDAP settings 6 1 2 3 4 In the Administrator Setting screen, touch [5 Network Setting]. (Refer to page 1-17 for more details. ) In the Network Setting screen, touch [4 LDAP Setting]. In the LDAP Setting screen, touch [2 Setting Up LDAP]. Touch the LDAP server button to register and specify the setting. Setting Up LDAP screen 1/6 appears. 6 Touch [Fwd. ]. Setting Up LDAP screen 2/6 appears. IC-402 6-13 Copier Network Functions Chapter 6 5 Specify the desired settings. 6 7 Specify the desired settings. Copier Network Functions 8 9 Touch [Fwd. ]. Specify the desired settings. Chapter 6 10 11 Touch [Fwd. ]. Setting Up LDAP screen 4/6 appears. Copier Network Functions Specify the desired settings. 12 Touch [Fwd. ]. Setting Up LDAP screen 5/6 appears. 6-14 IC-402 Copier Network Functions 6 13 Specify the desired setting. 14 15 Touch [Fwd. ]. Specify the desired settings. 16 Touch [OK]. The LDAP server registration and authentication are set. Note To cancel changes to the setting, touch [Cancel]. To quit specifying the Utility mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode by touching [Close] in each screen until the screen for the Copy, Fax, Scan or Box mode appears. 2 Reminder If the LDAP server settings are not specified correctly, network failure may occur. The server administrator should specify LDAP settings. IC-402 6-15 Copier Network Functions 2 Chapter 6 6 2 Note Copier Network Functions Be sure to use an authentication method like the one that is used by the LDAP server. For details, refer to the manual of the LDAP server being used. "GSS-SPNEGO" is specified as the authentication method when the LDAP server uses Active Directory. If "GSS-SPNEGO" is specified, enter the domain name for Active Directory. ! Detail Depending on the authentication method, settings for the following parameters must be set correctly on the Setting Up LDAP screen (6/6) in order to perform the "Check Connection" operation. [. . . ] 1-15, 2-5 Scan settings . . . . . . . . . . . . . . . . . . . . . . . 1-10, 2-52 Scan size setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-60 Scan to e-mail . . . . . . . . . . . . . . . . . . . . . . . . . 1-3, 2-6 Scan to FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]