User manual KONICA MINOLTA KONICA7915-7920-SG-00

[. . . ] Contents Names and Functions of Control Panel Parts . . . . . . . . . . . . . 1 To load paper into the 1st drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Loading the Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] z Press to reset the number of copies to "1". z Press to erase a setting, such as the zoom ratio or size, selected using the keypad. 4 [C] (clear) key 5 [Panel Reset] key z Press to reset all copy functions and settings to their defaults. (All selected settings are cancelled. ) * Stored zoom ratios, stored job settings, and interrupted or delayed copy jobs are not cancelled. 6 7 [Stop] key [Start] key z Press to stop a continuous copy operation. z If this key is pressed while the copier is warming up, the copy job is delayed until the copier is finished warming up. z The [Start] key indicator lights up in green to indicate that the copier can begin copying. The [Start] key indicator lights up in orange to indicate that the copier cannot make copies. Konica 7915/7920 1 Loading the Paper To load paper into the 1st drawer Use the 1st drawer when making copies onto normal paper of either standard or non-standard sizes, or onto special paper such as overhead projector transparencies, postcards, or thick paper. 1 Pull out the paper drawer for the 1st drawer. Paper take-up roller Note Be careful not to touch the surface of the paper take-up roller with your hands. C4004O501AA 2 Press down on the paper-lifting plate until it locks into place. C4004O502AA 3 Slide the paper guides to fit the size of paper to be loaded. C4004O503AA 2 Konica 7915/7920 4 For 12-1/4" × 18" or "A3WIDE" paper, adjust the trailing-edge guides as shown in the illustration. C4004O504AA 5 Load the paper into the drawer so that the front side of the paper (the side facing up when the package was unwrapped) faces up. Note Do not load so much paper that the top of the stack is higher than the M mark. C4004O505AA C4007O162CA 6 Close the paper drawer. C4004O506AA Konica 7915/7920 3 7 Turn the paper type dial on the drawer to the setting for the type of paper loaded. C4004U075CA To load paper into the 2nd drawer 1 Pull out the paper drawer for the 2nd drawer. Paper take-up roller Note Be careful not to touch the surface of the paper take-up roller with your hands. C4004O507AA 2 Press down on the paper-lifting plate until it locks into place. C4004O508AA 4 Konica 7915/7920 3 Remove the trailing-edge guide, and then re-install it for the size of paper to be loaded. 3 4 C4004O509AA 4 Slide the lateral guides to fit the size of paper to be loaded. C4004O510AA 5 Load the paper into the drawer so that the front side of the paper (the side facing up when the package was unwrapped) faces up. Note Do not load so much paper that the top of the stack is higher than the M mark. C4004O511AA C4007O162CA 6 Close the paper drawer. Konica 7915/7920 5 To load paper into the manual bypass tray Paper can be fed manually through the manual bypass tray if you wish to copy onto paper that is not loaded into a drawer, or if you wish to copy onto special paper, such as overhead transparencies, postcards, or thick paper 1 or 2. 1 Open the manual bypass tray. C4004O512AA 2 Adjust the paper guides to fit the size of paper to be loaded, and then lightly insert the paper as far as possible. When paper is loaded into the manual bypass tray, a screen that allows you to select the paper size appears. (Refer to "To copy onto manually fed paper" on page 13. ) C4004O513AA Note Copies will be made on the surface of the paper facing down when it is loaded into the manual bypass tray. 6 Konica 7915/7920 To position the document on the original glass 1 2 Lift open the original cover, or the duplexing document feeder if it is installed. Position the document face down onto the original glass. C4004O516AA 3 Align the corner of the document with the arrow marks on the document scales above and to the left of the original glass. C4004O025EA 4 Carefully close the original cover, or the duplexing document feeder if it is installed. Konica 7915/7920 7 Positioning the Document To load the document into the duplexing document feeder 1 Slide the adjustable document guide to fit the size of the documents. C4004O517AA 2 Load the documents face up into the document feed tray. C4004O518AA 8 Konica 7915/7920 To make a basic copy 1 Press the [Copy] key to enter Copy mode. C4004O519CA 2 Position the document(s) to be copied. (Refer to "Positioning the Document" on page 9. ) C4004O516AA C4004O518AA 3 Select the desired color mode (Auto Color, Full Color, or Black). C4004O205CA Konica 7915/7920 9 Making Copies 4 Make sure that the Basic screen is displayed, and then specify any necessary settings, such as the desired paper tray or the density. C4004P001CA 5 Using the keypad, enter the number of copies (between 1 and 100) that you wish to make. C4004O187AA 6 Press the [Start] key to begin making copies. To stop copying before the set number of copies are made, press the [Stop] key. C4004O520CA 10 Konica 7915/7920 To copy onto manually fed paper 1 Position the document(s) to be copied. C4004O516AA C4004O518AA 2 Select the desired color mode. C4004O205CA Konica 7915/7920 11 3 Open the manual bypass tray. C4004O512AA 4 Adjust the paper guides to fit the size of paper to be loaded, and then load the paper so that the front side of the paper faces down. [. . . ] In addition, a lit " " indicates areas where paper may have been misfed and that should be checked. Duplexing document feeder p. 21 Konica 7915/7920 17 Clearing a Paper Misfeed To clear a paper misfeed in the manual bypass tray 1 Pull up the lock release lever to open the right-side door. C4004O529AA CAUTION Decreased copy quality may result if the surface of the image transfer belt at the bottom of the copier's fusing unit is touched. [. . . ]