User manual KONICA MINOLTA MAGICOLOR 2430

[. . . ] magicolor 2430 DL User's Guide ® 4139-7743-06A 1800769-001F Thank You Thank you for purchasing a magicolor 2430 DL. Your magicolor 2430 DL is specially designed for optimal performance in Windows, Macintosh, and other environments. Trademarks KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. magicolor is a trademark or registered trademark of KONICA MINOLTA PRINTING SOLUTIONS U. S. A. , INC. Copyright Notice Copyright © 2006 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. , Marunouchi Center Building, 1-6-1 Marunouchi, Chiyoda-ku, Tokyo, 100-0005, Japan. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Notice KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. [. . . ] Do not manually rotate the toner cartridge carousel. In addition, do not rotate the carousel with force, otherwise it may be damaged. Note Dispose of the empty toner cartridge according to your local regulations. Do not burn the toner cartridge. 5 6 Prepare a new toner cartridge. Shake the cartridge a few times to distribute the toner. Make sure that the toner roller cover is securely attached before shaking the toner cartridge. Replacing Consumables 69 7 Remove the cover from the toner roller. Do not touch or scratch the toner roller. 8 Align the shaft on each end of the toner cartridge with its holders, and then insert the cartridge. Before inserting the toner cartridge, make sure that the color of the toner cartridge to be installed is the same as the label on the toner cartridge carousel. 9 Press down on the toner cartridge until it snaps into place. 70 Replacing Consumables 10 Close the front cover. 11 Carefully close the top cover. The printer must complete a calibration cycle (less than 2 minutes) after the toner cartridge has been replaced. If you open the top cover before the message READY appears, the printer stops and repeats the calibration cycle. Replacing Consumables 71 Replacing the Drum Cartridge 1 Pull the lever, and then open the top cover. If there is paper in the output tray, remove it. Fold up the output tray before opening the top cover. Do not touch the transfer belt. 2 Carefully pull out the drum cartridge. Note Dispose of the used drum cartridge according to your local regulations. Do not burn the drum cartridge. 72 Replacing Consumables 3 Prepare a new drum cartridge. Do not touch the PC drum on the drum cartridge. 4 Install the new drum cartridge. Replacing Consumables 73 5 Carefully close the top cover. The printer must complete a calibration cycle (less than 2 minutes) after the drum cartridge has been replaced. If you open the top cover before the message READY appears, the printer stops and repeats the calibration cycle. 74 Replacing Consumables Maintaining the Printer Maintaining the Printer CAUTION Read all caution and warning labels carefully, making sure to follow any instructions contained in them. These labels are located on the inside of the printer's covers and the interior of the printer body. Handle the printer with care to preserve its life. Abuse handling may cause damage and void your warranty. If dust and paper scraps remain on the inside or outside of the printer, printer performance and print quality will suffer, so the printer should be cleaned periodically. Keep the following guidelines in mind. WARNING! Turn off the printer, unplug the power cord, and disconnect all interface cables before cleaning. Do not spill water or detergent into the printer; otherwise the printer will be damaged and an electric shock may occur. CAUTION The fuser unit is hot. When the top cover is opened, the fuser unit temperature drops gradually (one hour wait time). Be careful when cleaning the inside of the printer or removing media misfeeds, as the fuser unit and other internal parts may be very hot. [. . . ] Since there are two hooks on the right side of the panel, remove the rear panel by slightly pulling the left side of the panel toward you, then sliding the panel off to the left. 4 Insert the new DIMM straight into the DIMM connector until the latches snap into the locked position. Observe the keyed side of the DIMM to align it with the connector. If you cannot snap the DIMM into place, do not force it. Reposition it, making sure that the DIMM is seated completely in the connector. 5 6 Reinstall the panel and tighten the screw. [. . . ]