User manual KONICA MINOLTA MICROPRESS DX MICROPRESS SX-DX PRINT SERVER OPERATOR MANUAL

[. . . ] Portions hereof include TextBridge® OCR Copyright ©Xerox Corporation. LZW data compression technology licensed under U. S. 4, 558, 302 All other company and product names are registered trademarks or trademarks of their respective owners in the United States and other countries. The following marks are used in this manual: Indicates precautions that must be observed to prevent possible personal injury or damage to equipment or malfunctioning of software. Indicates notes and memos containing additional or detailed information. Indicates useful tips. T/R Systems, Incorporated 1300 Oakbrook Drive Norcross, GA 30093 U. S. A Phone: (770) 448­9008 Fax: (770) 448­3202 Sales and Marketing Phone: (770) 448­9008 Fax: (770) 448­3202 E-Mail: micropress@trsystems. com Technical Support Phone: (770) 448­7074, (800) 649­5819 Fax: (603) 849-7769 E-Mail: support@trsystems. com World Wide Web: http://support. trsystems. com Internet Access World Wide Web: http://www. trsystems. com Table of Contents Regulatory Statements. Notice for EMC Directive (220-240 V model only) . [. . . ] For a rated current up to 6A, a type not lighter than H05VV-F 3G 0. 75 mm2 or H05VVH2-F 3G 0. 75 mm2 shall be used. · Be sure to turn off the power before unplugging or plugging in the equipment power cords or interface cables. · When moving the equipment be sure to turn off the power before unplugging the power cable. Also, be sure and check for sharp edges before you grip or handle the Copier/ Printer. · Be sure to unwind the power cord prior to plugging it in. Using it tied up may lead to damage, overheating, short-circuit or result in fire. · Be sure to fully plug the power cord into the power outlet, as any flammable material caught between an opening may result in fire. However, if this is unavoidable, be sure to take the following precautions. Failure to do this may lead to overheating, resulting fire, or cause flickering due to a drop in voltage. Be sure not to exceed the allowed rating current of the extension cord. Do not connect several extension cords together as this is dangerous. Do not attempt to service the equipment by yourself, except as instructed in the manual. Opening or removing those covers that are intended to be removed only by qualified service personnel, may expose you to dangerous voltage points or other risks. Refer all servicing in those compartments to qualified service personnel. 2 Warning: · The equipment should never be placed near or over a radiator, heat register, or flame. · This equipment should not be placed in a built-in installation unless proper ventilation is provided. · Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the equipment and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the printer on a bed, sofa, shag rug, or other similar surface. · Before connecting the printers to a power source, check the voltage rating label on the rear of the equipment to ensure that the printer voltage matches that of the power source. If a voltage label is missing, contact the nearest authorized dealer or the place of purchase before operating equipment. · If the extension cord is used with the equipment, make sure that the total ampere rating of the products plugged into the extension cord does not exceed the extension cord ampere rating. · The power cord should be routed so that it is not likely to be walked on or pinched by items placed on or against it. [. . . ] The grounding-type plug will only fit a grounding-type AC outlet. If a grounding-type AC outlet is not available, contact a licensed electrician to replace the existing outlet with one that is properly grounded. Warning: · Do not overload the AC outlet and extension cords as this may cause fire or electrical shock. · Route the power cords so that they are not likely to be walked on or pinched by items placed on or against them Operating Environment Place the MicroPress System in a location where the following conditions are met: · The location is flat and steady. [. . . ]