User manual KONICA MINOLTA PAGEPRO 5650

[. . . ] pagepro 4650EN/5650EN User's Guide A0DX-9561-01A 1800850-001B Thank You Thank you for purchasing a pagepro 4650EN/5650EN. Your pagepro 4650EN/5650EN is specially designed for optimal performance in Windows, Macintosh and Linux environments. Trademarks KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. pagepro and PageScope are trademarks or registered trademarks of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. All other trademarks and registered trademarks are the property of their respective owners. Copyright Notice Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. , Marunouchi Center Building, 1-6-1 Marunouchi, Chiyoda-ku, Tokyo, 100-0005, Japan. [. . . ] See also "PAPER MENU" on page 36. Other Media When loading media other than plain paper, set the media mode (Envelope, Label, Thick 1, Thick 2, Thick 3, Postcard, Thin paper, or Transparency) in the driver for optimum print quality. Loading Media 95 Loading Envelopes The following procedure is given taking Envelop #10 as an example. 1 Load the envelope with its flap side down. Open Tray 1. 2 Remove the lid of the tray. 3 If the media pressure plate is raised, press down the media pressure plate to lock it into place. 96 Loading Media 4 Load the envelope with its flap to the right. For the information on the tray capacity for each media, see "Media Types" on page 85". For envelopes with the flap along the short edge, load the envelopes with the flap side down. Squeeze the media guide (length) and slide it to the desired size. 5 6 Squeeze the media guide (width) and slide it to the desired size. Loading Media 97 7 Reattach the lid of the tray. 8 Push the tray completely into the printer. 9 Select PAPER MENU/PAPER SOURCE/TRAY X (TRAY 1/2/3/ 4)/PAPER SIZE and PAPER TYPE in the configuration menu, and then select the setting for the size and type of the media that is loaded. See also "PAPER MENU" on page 36. 98 Loading Media Loading Label sheets/Postcards/Thick Stock/Thin paper/ Transparencies Transparencies for full-color printing cannot be used. Using them may lead to a printer malfunction. Remove transparencies as soon as they are output to the center output tray to prevent them sticking together. Open the tray and place it on a flat surface. 1 2 Remove the lid of the tray. 3 If the media pressure plate is raised, press down the media pressure plate to lock it into place. Loading Media 99 4 Squeeze the media guide (length) and slide it to the desired size. 5 Squeeze the media guide (width) and slide it to the desired size. 6 Load the paper face up in the tray. For the information on the tray capacity for each media, see "Media Types" on page 85. 100 Loading Media 7 Reattach the lid of the tray. 8 Push the tray completely into the printer. 9 Select PAPER MENU/PAPER SOURCE/TRAY X (Tray 1/2/3/ 4)/PAPER SIZE and PAPER TYPE in the configuration menu, and then select the setting for the size and type of the media that is loaded. See also "PAPER MENU" on page 36. Loading Media 101 Loading the Paper Larger than A4 1 Open the tray and place it on a flat surface. 2 Remove the lid of the tray. 3 Slide the right and left lock tabs in the tray outwards to unlock them. Plain paper Envelope 102 Loading Media 4 Hold the grip of the tray and pull its extendable part to the front until it reaches the desired paper size. 5 Squeeze the media guide (length) and slide it to the desired paper size. 6 Squeeze the media guide (width) and slide it to the desired paper size. Loading Media 103 7 Load the paper face up in the tray. For the information on the tray capacity for each media, see "Media Types" on page 85. 8 Reattach the lid of the tray. 9 Push the tray completely into the printer. 10 Select PAPER MENU/PAPER SOURCE/TRAY X (Tray 1/2/3/ 4)/PAPER SIZE and PAPER TYPE in the configuration menu, and then select the setting for the size and type of the media that is loaded. See also "PAPER MENU" on page 36. 104 Loading Media Loading Banner paper in the Tray 1 1 Open the tray and place it on a flat surface. 2 Remove the lid of the tray. 3 Slide the right and left lock tabs in the tray outwards to unlock them. Plain paper Envelope Loading Media 105 4 Hold the grip of the tray and pull its extendable part to the front until it reaches the end. 5 Squeeze the media guide (length) and slide it to the desired paper size. 6 Squeeze the media guide (width) and slide it to the desired paper size. 7 Load the banner paper face up in the tray, and then roll up the end of the paper so that it does not fall off the tray. 106 Loading Media 8 Push the tray completely into the printer. 9 Select PAPER MENU/PAPER SOURCE/TRAY 1/PAPER SIZE and PAPER TYPE in the configuration menu, and then select the setting for the size and type of the media that is loaded. See also "PAPER MENU" on page 36. Loading Media 107 Duplexing Select paper with high opacity for duplex (double-sided) printing. Opacity refers to how effectively paper blocks out what is written on the opposite side of the page. If the paper has low opacity (high translucency), then the printed data from one side of the page will show through to the other side. Check your application for margin information. For best results, print a small quantity to make sure the opacity is acceptable. Duplex (double-sided) printing can be done manually or can be done automatically with the duplex option installed and selected. For installing the duplex, refer to "Installing the Duplex" on page 205. Note For details on supported media types for duplex printing, see "Media Specifications" on page 84. Duplexing envelopes, labels, thick paper3 or transparencies is not supported. Duplex printing can be performed with enough memory (no less than 256 MB) installed in the printer. How do I autoduplex? You should verify that the duplex is physically installed on the printer to successfully duplex (double-sided) the job. [. . . ] (Do not remove them from the printer. ) 5 Remove the panel. 6 Plug the cable on the CF Adapter into the connector on the controller board. 202 CompactFlash 7 Mount the CF Adapter onto the controller board as shown in the figure, and then secure the screws. 8 Fully insert the CompactFlash card into the appropriate slot. When the CompactFlash card is correctly inserted, the button on the side of the slot (circled in the illustration) slightly pops out. Before removing the CompactFlash card, press this button. 9 10 11 12 Reinstall the panel and tighten the two screws. Reconnect the power cord, and turn on the printer. CompactFlash 203 13 Declare the Memory card in the Windows printer driver (Properties/Configure tab). 204 CompactFlash Duplex Duplex (double-sided) printing can be performed automatically with the duplex and enough memory installed. [. . . ]