User manual KONICA MINOLTA PC-201 UNPACKING/SET-UP INSTRUCTIONS

[. . . ] Check that the following accessories are available in the box. 1 Fixing Leg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Fixing Leg Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Fixing Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 Shoulder Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 Screw (9646-0408). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6 Paper Size Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 7 Installation Manual (this manual) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 2 3 4 4348U004AA 4348U020AB 4348U099AB 4658U021AA 4658U022AA 5 6 7 9646040813 . Remove the protective tape from the inside of the drawer. NOTE Do not peel off the tape that fixes the Paper Feed Cabinet hookup harness in position until the machine is attached to the Paper Feed Cabinet. 4348U119AA Hookup Harness 4348U118AA ­2­ PC-201 I Attaching the machine to the Paper Feed Cabinet 1. [. . . ] Install the Fixing Legs at two locations in the front shown in the illustration (six screws y furnished with the Paper Feed Cabinet). Slide out the 3rd and 4th Drawer. z 4348U023AD y x 3. Install the Fixing Leg Covers at two locations in the front shown in the illustration (2 Pieces). NOTES · Insert the Fixing Leg Covers in the direction shown by arrow until they click into position. · Insert the Protruded Portions of the cover shown by the arrows into the Fixing Leg. Install the Fixing Legs at two locations in the rear shown in the illustration. (six screws furnished with the Paper Feed Cabinet). Load the paper stack so that it rests below the tab fitted to the Edge Guide. 4348U095AA 4348U100AC 4348U102AB x z z y 4348U024AD x 5. Install the Fixing Leg Covers at two locations in the rear shown in the illustration (2 Pieces). NOTES · Insert the Fixing Leg Covers in the direction shown by arrow until they click into position. · Insert the Protruded Portions of the cover shown by the arrows into the Fixing Leg. NOTES · Make sure that the top level of the paper stack does not exceed the M (MAX) paper level indicator. · Slide the Edge Guide tightly up against the edge of the paper stack so that there is no gap between them. · With the Trailing Edge Stop, fit its locking tab properly into the slit at the correct paper size position. · Correct any curl in the paper before loading. 4348U101AC 4348U102AB ­4­ PC-201 I Installing the Ornamental Cover 1. Install the Ornamental Cover attached to the machine (two screws). I Checking and Adjusting the Paper Reference Position 1. Plug the power cord into the power outlet and turn on the machine. (For details of how to display the Tech. Mode screen, see the Service Manual. ) 4348U049AA 4036P031CA 3. Affix the Paper Size Label furnished with the Paper Feed Cabinet to the location shown in the illustration. (The size label is similarly put on the 4th. ) 4348U052AA 4036P036CA 5. [. . . ] · If width A is greater than the specified value, move the Edge Guide toward the front. · If width A is smaller than the specified value, move the Edge Guide toward the rear. 4348U009AA A Paper Exit Direction C4658U028AA 12. Load paper and let the machine produce another test print. * Make the adjustment until width A falls within the specified range. [. . . ]