User manual KONICA MINOLTA PI7200E PAGESCOPE LIGHT OPERATOR MANUAL

[. . . ] Apple and Macintosh are registered trademarks of Apple Computer, Inc. Ethernet is a registered trademark of Xerox Corporation. EFI, Fiery and the Fiery logo are registered trademarks of Electronics For Imaging, Inc. Patent and Trademark Office and/or certain other foreign jurisdictions. [. . . ] If an error message appears due to an incorrect setting, click the Back button to return to the previous page, and then try specifying the setting again. In addition, if the PageScope Light logo in the top-left corner of the page is clicked, the About page opens up. If the PageScope Light logo in the About page is clicked, the web site opens up in the browser. 2 2 Access 2. 2 Entering the Password To enter administrator mode, type the password into the "Admin Password" box in the upper-left corner of the screen, and then click the [Login] button. If the correct password was entered, you will be logged into the administrator mode and the [Logout] button appears. The PageScope Light settings can only be changed from the administrator mode. Note that the password is case-sensitive, so be sure to type in uppercase and lower-case characters correctly. (The password you should type in here is the same as the administrator password you created with Fiery Controller. ) If a password is entered, that password will be valid in ten minutes. In the case of Admin mode on PageScope Light, following area become effective. · · · · · · Preference Maintenance (Reset/Initialize) Online Assistance General Setting PCL Setting PostScript Setting 3 3 Screen Configuration 3 Screen Configuration The configuration of the PageScope Light screen is shown below. Status display section The status of the printer and scanner is shown with icons and text. Ready Attention Error Trouble 4 3 Screen Configuration Tabs The categories that can be controlled by PageScope Light are displayed. · System · Print · Network Used to control and set the system structure for the Di7210/Di5510 Used for setting the printer controller Used to confirm the network settings Menus The information and settings for the selected tab are displayed. Information and setting details The details of the selected menu are displayed. Fiery WebTools Logo (Available for HDD Option) Clicking this logo displays the settings page for Fiery WebTools, which is built into the printer controller. For details about Fiery WebTools, see the Fiery Printing Guide. 5 4 Description of Each Page 4 Description of Each Page This section contains descriptions of the information and settings that are displayed when each tab is clicked. 4. 1 System Tab On the System tab, information concerning the system structure for the Di7210/Di5510 can be checked and set. Checking and setting can be performed with the Summary, Details, Preference, Maintenance and Online Assistance menus. Summary A summary of the status and the system structure of the Di7210/ Di5510 is displayed. Details The details of the status and the system structure of the Di7210/ Di5510 are displayed. · Input Tray It shows the current status of all the Input Trays installed on the Di7210/Di5510. 6 4 Description of Each Page · Output Tray It shows the current status of all the Output Trays installed on the Di7210/Di5510. · Hard Disk It shows the status of the hard disk installed on the printer controller. · ROM Version It shows version of firmware installed on the Di7210/Di5510 and printer controller. · Interface Info It shows information about network interface and local interface. · Consumable It shows the current status of Di7210/Di5510 consumables. Preference The environment settings such as the refresh rate time and the system language can be specified. Maintenance The printer controller can be reset/initialized and counter values can be checked. · Counter · Reset · Initialize The total number of prints made since the Di7210/ Di5510 was set up can be checked. Clicking the [Reset] button resets the printer controller. Clicking the [Restore] button restores the initial factory default settings of the printer controller. Online Assistance (Available for HDD Option) Enter information concerning product support and check it when necessary. 7 4 Description of Each Page 4. 2 Print Tab Use the Print tab for configuring the printer controller settings. Checking and setting can be performed with the Default Set, Test Print, and Font Info menus. Default Set You can use this menu to make various printer settings. · General Setting You can use this menu to make general print settings. Print Number Set the number of copies to be printed. [. . . ] Print to PostScript Error Specify whether or not a PostScript error is printed. 9 4 Description of Each Page Test Print It lets you select test print pages and execute a test print operation. You can print Configuration Page, PCL Demo Page, PostScript Demo Page, PCL Font List, and PostScript Font List. Font Info It shows a list of fonts built into the printer controller. · PCL Font It shows a list of PCL fonts built into the printer controller. · PostScript Font (Available for HDD Option) It shows a list of PostScript fonts built into the printer controller. 10 4 Description of Each Page 4. 3 Network Tab Use the Network tab for confirming the network settings of the printer controller. Checking can be performed with the Summary menu. Summary The printer controller network settings are displayed so they can be checked. Device Type Either "Ethernet 10/100 BaseT" or "Token Ring" is displayed. [. . . ]