User manual KONICA BIZHUB 750

[. . . ] 750/600 User Manual x Introduction Introduction Thank you for choosing this machine. This manual contains details on the operation of the various functions of the machine, precautions on its use, and basic troubleshooting procedures. In order to ensure that this machine is used correctly and efficiently, carefully read this manual before using the machine. After reading the manual, store it in the designated holder so that it can easily be referred to when questions or problems arise during operation. [. . . ] The Basic screen appears again. bizhub 750/600 7-15 7 Two non-standard paper sizes can be stored. Copy paper/original To store a non-standard paper size (Custom Size settings store) Storing paper sizes that are used often allows the paper size to be quickly selected, without having to re-enter the setting. 1 In the Basic screen, touch [Paper]. The Paper screen appears. 2 Touch the button for the bypass tray, and then touch [Change Tray Settings]. 7-16 bizhub 750/600 Copy paper/original 7 3 Touch [Custom Size]. 4 Specify the X and Y sides of the paper, and then touch [Store]. ­ ­ ­ ­ ­ Make sure that [X] is selected, and then use the keypad to type in the length of side X. (139. 7 mm to 458. 0 mm) Touch [Y] to select it, and then use the keypad to type in the length of side Y. (100. 0 mm to 314. 0 mm) Check the illustration in the screen for the sides that are considered as X and Y. If a value outside of the allowable range is specified, the message "Input Error" appears. Type in a value within the allowable range. If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. bizhub 750/600 7-17 7 5 Touch [memory1] or [memory2]. Copy paper/original ? How can the name of the stored paper size be changed?% Touch [Custom Name], then type the new name into the Custom Name screen that appeared, and then touch [OK]. % Use the keyboard that appeared in the screen to type in the new name, and then touch [OK]. % For details on typing in text, refer to "Entering text" on page 13-2. 6 Touch [OK] four times. The Basic screen appears again. 7-18 bizhub 750/600 Copy paper/original To select a setting for oversized paper (Oversized Paper settings) 7 If oversized paper is loaded into the bypass tray, it will be necessary to specify the paper size. Oversized paper is larger than the standard size and allows copies of standard-sized original to be printed so that there is no loss at the edges. For example, if A3 Wide paper is used, an area up to 314 mm × 458 mm can be printed, allowing the entire area of an A3-size original to be printed. 1 In the Basic screen, touch [Paper]. The Paper screen appears. 2 Touch the button for the bypass tray, and then touch [Change Tray Settings]. bizhub 750/600 7-19 7 3 Touch [Oversized Paper]. Copy paper/original The Oversized Paper screen appears. 4 Select the size of the paper to be loaded and image adjustment. ­ To select a paper size in inches, touch [Inches]. The list of paper sizes in inches appears. 5 6 To change the size, touch [Change Size]. The Change Size screen for oversized paper appears. Specify the length (X) and width (Y) of the paper, and then touch [OK]. ­ ­ ­ Make sure that [X] is selected, and then use the keypad to type in the length of side X. (Maximum 458 mm) Touch [Y] to select it, and then use the keypad to type in the length of side Y. (Maximum 314 mm) If a value outside the allowable range is specified, the message "Input Error" appears. Type a value within the allowable range. The allowable range differs depending on the paper sizes. 7-20 bizhub 750/600 Copy paper/original ­ 7 If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. 7 Touch [OK] four times. The Basic screen appears again. 2 Note The selected size button is programmed with the entered paper size, so that the paper size is available to be selected again without having to be typed in. [. . . ] 4-7 Toner cartridge . . . . . . . . . . . . . . . . . . . . . . . . 2-4, 9-5 Toner-cartridge-securing lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6, 9-5 Total counter . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4, 2-16 Touch panel adjustment . . . . . . . . [. . . ]