User manual KONICA BIZHUB PRO 1050P REPLACEMENT INSTRUCTIONS

[. . . ] / CMS REPLACEMENT INSTRUCTIONS (Customer Maintenance Support) CMS REPLACEMENT INSTRUCTIONS 1. Main body : Pick-up roller assembly/separation roller assembly 2. Main body : Transfer/separation charger unit 5. DF-603 : Pick-up roller unit/separation roller unit 6. [. . . ] Be sure to set the guide pin to the concave portion at the bottom of the fusing unit. Jam handling knob 3. Screw [1] With the fusing unit set to the reverse/exit section, slide the fusing unit to the rear side until it hits against the rear. NOTE · Be sure to slide the fusing unit until it hits against the rear. 4. 5. With the fusing unit pressed against the rear side, fix it with the screw [1]. Attach the lever assist plate with the screw [2]. Lever assist plate Screw [2] 1050fs2003y 6. 7. Open the fusing paper exit section. With a driver inserted into the hole of the shaft, rotate the shaft counterclockwise (in the arrowmarked direction) until it cannot turn any more to give pressure upon the fusing roller. Fusing paper exit section Shaft Hole Driver 1050fs2004z 23 2. Main body: fusing section replacement instructions 8. Screw Reverse/ exit section Install the fusing cover and fasten it with the 2 screws. Close the reverse/exit section. Fusing cover Fusing paper exit section 1050fs2002z 11. Push in the ADU while holding the pull-out lever by hand, and then lock the pull-out lever. NOTE · When the ADU is brought back to its original position, be sure to lock the pull-out lever. ADU Pull-out lever 1050fs2001w Front door Main power switch /Left Front door /Right 12. Plug the power cord into the wall outlet. Turn ON the main power switch and close the front door /Left and the front door /Right. 1050fs2001x 24 2. Main body: fusing section replacement instructions 14. Turn ON the sub power switch. Sub power switch 1050fs5012z 25 3 Main body: Cleaning web Cleaning web REPLACEMENT INSTRUCTIONS 2004. 10 Ver. Main body: cleaning web replacement instructions (1) Purpose To return to the normal operation as soon as possible after completion of the wind-up of the cleaning web. (2) Procedure for removal 1. Turn OFF the sub power switch. Sub power switch 1050fs5012z Front door Main power switch /Left 2. Front door /Right Open the front door /Right and the front door / Left, and then turn OFF the main power switch. Unplug the power cord from the wall outlet. 3. Caution: · When conducting the replacement operations, be sure to turn OFF the main power switch and the sub power switch and then unplug the power cord from the wall outlet. · The cleaning web is installed at the fusing unit. Since the fusing unit is very hot immediately after each of the power switches is 1050fs2001y turned OFF, you may get burnt. Be sure to conduct the operation after the fusing unit cools down sufficiently. 27 3. Main body: cleaning web replacement instructions 4. Bring down the pull-out lever to the right side while pressing with a driver the lock release lever in the arrow-marked direction, and pull out the ADU. ADU Pull-out lever Lock release lever 1050fs2001z 5. Web cover Remove the 2 screws and then remove the web cover. Screw 1050fs2163c 28 3. Main body: cleaning web replacement instructions 6. Release the couplings provided at the 2 places in the arrow-marked direction and remove the used cleaning web. Cleaning web 7. When installing a new replacement part, see "(3) Procedure for reinstallation" (on the next page). Couplings 1050fs2164c 29 3. Main body: cleaning web replacement instructions (3) Procedure for reinstallation Driven couplings /Rear Shaft on the unused side 1. Set the shaft on the unused side of the new cleaning web to the driven couplings /Rear and / Front. Notch NOTE · Be sure to set each of the detent on the driven couplings to the notch of the wind-up shaft. Detent When the web is installed in the wrong direction, it does not coincide with the notch. 2. Hold either side of the wind-up shaft of the new cleaning web with both hands, and take up the new cleaning web until the blue line disappears. Wind-up shaft NOTE Cleaning web · The performance of the new cleaning web is guaranteed from the position in which the blue line disappears. Be sure to take up the cleaning web up to this position. Blue line Either side Driven couplings /Front Notch Shaft on the unused side Detent 1050fs2165c 30 3. [. . . ] Remove the 2 screws and then remove the entrance guide plate. Entrance guide plate pf701fs2006c 50 6. PF-701: pick-up roller unit/separation roller unit replacement instructions Screw 13. Remove the 2 screws and release the fixing of the separation roller unit. Separation roller unit pf701fs2007c Coupling pin Joint 14. Pull out the front side of the separation roller unit in the arrow-marked direction, and then remove the coupling pin in the rear from the joint. [. . . ]