User manual KONICA CR-241

[. . . ] The instruction must be strictly adhered to. Disconnect the AC power cord from the AC outlet. Connect the grounding terminal as instructed. Denotes a sentence regarding safety precaution for laser. [. . . ] Doing so may damage the VIVID 910 or memory card. Note 21 Notes When Using the Instrument with Tripod When using the instrument with the tripod, first attach the tripod base plate to the instrument, and then attach the instrument to the panhead/tripod. To improve scanning accuracy, it is recommended that scanning be performed via the personal computer connected to the instrument, instead of pressing the [RELEASE] key. CAUTION · Make sure that the tripod base plate, panhead and tripod are secured to the instrument and each fastener on the tripod is firmly tightened. Failure to observe this point may result in the tripod overturning or the instrument dropping. · When placing the tripod on a floor, examine the floor conditions and flatness to make sure that the tripod is stably placed. · After measurement is completed, the instrument must be removed from the tripod before storing them. If the instrument is stored with the tripod attached, the tripod may overturn or the instrument may drop, resulting in accidents. Mounting to the Tripod 1. Mounting the Tripod base plate to the Instrument Before mounting the instrument to the tripod, mount the tripod base plate to the instrument as explained below. Memo · Five screw holes for the tripod base plate are provided on both the top and base of the instrument. · The instrument can be attached upside down to the tripod. In this case, remove the handle from the top of the instrument, mount the tripod base plate on the top of the instrument, then mount the handle on the base of the instrument. [Mounting the Tripod base plate] 1 2 3 Make sure that the power to the instrument is OFF, and remove the power cord. Turn the instrument slowly so that its side faces down, and place it on a flat table. Place the tripod base plate on the base (or top) of the instrument, and secure it with the five screws (supplied with the tripod base plate). · Align the red mark on the lens with the one on the lens mount socket, and insert the lens until a click is heard. Memo · The position of the red mark on the lens varies with the focus point. · Hold the ring with your finger located near the red mark on the lens. This will facilitate inserting the lens. 5 Turn the lens fixing ring clockwise to secure the lens. 28 Replacing the Lens 6 Attach the lens hood. Make sure that the notch is aligned with that on the lens, and turn the hood. Memo The hood must be turned until it contacts the bayonet mount socket. 7 Press any key. After approximately 10 seconds, "PLEASE OPEN LASER BARRIER AND PRESS ANY KEY" will be displayed on the viewfinder. The MENU view will appear. 8 29 Scanning the Object WARNING Never stare into the laser emitting window. Do not place a lens, mirror or optical element in the passage of the laser beam. Doing so may converge the laser beam, resulting in damage to your eyes, burns or fire. To prevent the above accidents, make sure that a wall or similar surface that does not reflect light is located behind the object. Memo For precise scan results, we recommend that you use a stable, flicker-free light source (such as a high-frequency fluorescent lamp). [Operating Procedure] 1 2 Press . to locate the arrow cursor to ®SCAN FILE LIST CAMERA SETTINGS CARD SETTINGS INFO 3 Press . The color image currently captured by the VIVID 910 will appear on the viewfinder. AF FINE Memo Auto-focus will be performed automatically, and "FOCUSING" will appear. [. . . ] Insert another memory card or press any key. 54 Error Messages Error Message (Alphabetically) MEMORY CARD IS EJECTED PRESS ANY KEY MEMORY CARD IS EJECTED RECORDING IS CANCELED PRESS ANY KEY SAME FILE NAME SYSTEM ERROR PLEASE TURN OFF Meaning The memory card has been ejected. Press any key. Action Insert a memory card into the slot. Insert a memory card into the slot. A file of the same file name already exists. Turn OFF the power. Specify another file name. Turn OFF the power, then turn it ON again. [. . . ]