User manual KORG AW2

[. . . ] Keeping foreign matter out of your equipment Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, fire, or electrical shock. Be careful not to let metal objects get into the equipment. A7 Clarinet / Clarinette Klarinette / Clarinete A8 Bassoon / Basson Fagott / Fagot THE FCC REGULATION WARNING (for USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Auto: The backlight will light brightly when sound is input or when a button is operated. When there has been no input or button operation for approximately ten seconds, the backlight will change to the "Soft" level of brightness. Use the input select button to choose the sound input. (Refer to "Recommended locations for attachment") The setting will alternate between MIC and PIEZO each time you press the button. If you want to change the reference pitch (calibration), press the CALIB [ ] or [ ] button. You can adjust this over a range of 410 Hz. The display will show the name of the note closest to the pitch detected. Tune your instrument to the correct pitch so that the desired note name appears. Once again play a single note on your instrument, and adjust the tuning so that the center segment of the meter is lit. The right (+) indicator will light if the pitch is too high, and the left (-) indicator will light if the pitch is too low. You have the option of reversing the direction of the AW-2’s meter between left and right, but in our explanation here we will assume that the High (+) indicator is located at the right side. M Recommended locations for attachment Instrument name Trumpet / Cornet Trombone Horn Single Double Tube Euphonium Flute Oboe E Clarinet B Clarinet Bass clarinet (B ) Bassoon Soprano saxophone Alto Saxophone Tenor saxophone Baritone saxophone Violin Viola Cello Contrabass Guitar Ukulele Banjo Mandolin Music Stand — — — — — — Clip Large Small Guitar Attachment location Main tube Bell (top) Mouthpiece receiver Bell (top right) First tube F slide Mouth pipe Bell *2 Bell body Bell joint area Bell Blowing tube Wing joint area Bell Neck / Main tube Neck Bell Head Head Tailpiece Tailpiece Head Head Head Head As desired B1 B1 B2 B2 B3 B3 B3 B3 C1 *3 A9 A8 A7 A6 A4 A5 *3 A2 A3 *1 Illustration Remarks A1 A1 Input select button Power button CALIB buttons Clip attachment slot Installing the battery Turn the power switch off before you install or replace the battery. The battery included with the AW-2 is for the purpose of verifying that the unit operates correctly, and may not have a very long life. When the battery begins to run low, the liquid crystal display (in particular the meter movement) will become fainter and the backlight will become dimmer. The AW-2 will continue to operate for a while longer, but tuning will become less accurate. Replace the battery as soon as possible. With the ball of your thumb, lightly press the battery cover located on the back of the AW-2, turn it counter-clockwise, and remove it. Replace the battery, being sure to observe the correct polarity so that the "+" side of the battery is visible. Turn the battery cover clockwise to reattach it. Attaching the included clip Large Clip Remove Yes Joint If you want to tune to a pure major third (-13. [. . . ] If you've selected the internal mic, you can also use the tuner without the clip. Please carefully attach the AW-2 to your instrument. Leaving the AW-2 attached for a long time may hurt the instrument surface. (clip) approximately 150/75/20 hours (backlight: unlit/soft/ auto, tuner continuously operating, A4 input) CR2032 lithium battery (3V) for checking operation Instrument clip Large Clip Guitar Clip Examples of using the joint Range of movement 360° By swapping the position of the guitar clip's joint socket (A) and non-slip cover (B), you can obtain a greater degree of freedom in how you attach the guitar clip to your instrument. [. . . ]