User manual KORG I2 SERVICE MANUAL

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] If you selected the effect that had been programmed, the Original icon in the multi-display will light. The five value knobs will be assigned to GAIN, TREBLE, MIDDLE, BASS, and LEVEL respectively, and will adjust the value of the corresponding parameter. (See p. 12, "Effect parameters. ") 5. As you rotate the knobs, the sound will change and the multidisplay will show the parameter name assigned to that knob and the current value. If you rotate the knob to adjust the value to the value it had before you began editing the original parameter value icon in the multi-display will light. The parameter assigned to the knob you moved Value of the parameter Edit icon Editing the effects The drive amp effect can be edited immediately by turning the value knobs or type knob; you do not have to press the DRIVE·AMP switch. (Refer to the section below, "Drive Amp effect Quick Edit function. ") To edit other effects, press the corresponding select switch to put that effect in Edit mode (the LED will blink). Channel A/B display DRIVE·AMP switch Drive Amp effect Quick Edit function You can edit the Drive Amp effect (unless the effect is turned off) by using the Type knob to re-select the effect, or by rotating the five value knobs to modify the parameter values. When you do so, the multi-display will show the effect name or parameter name assigned to the corresponding knob, and its current value. Even when another effect such as Modulation or Pedal is in edit mode, you can still turn the type knob to edit the drive amp effect. Editing is not possible if other functions are assigned to the value knobs, nor in Bypass, Mute, or Phrase Trainer modes. Parameter Original icon Value of the parameter Drive amp channel For each program, the Drive Amp effect has settings for two channels, A and B. Press the DRIVE·AMP switch located at the right of the panel to select the channel you will edit. Each time you press the switch, the LED will change between green (channel A) and red (channel B). If you do not wish to use the Drive Amp effect, use the Type knob to select OFF so that the Drive Amp effect will be bypassed, and the multi-display will indicate "DRV OFF. " In this case, the LED beside the DRIVE·AMP switch will go dark. 9 3. If you turn off the power or select a different program without writing the program, the program name you edited will revert to its previous setting. Writing programs Here's how to write an edited program. Press the WRITE switch, and the Multi-display will indicate "WRITE. " The number LED will blink. Use the UP and DOWN switches to select the destination for your program. Press the WRITE switch once again, and the display will read "COMPLT" to indicate that the program has been written. If you decide not to write, press the EXIT switch to cancel the Write operation. SPEED DEPTH FEEDBACK MIX MOD switch If you write an edited program to a different program number, the program that was overwritten will be lost. It is not possible to write to a preset program. Parameter 4. Appendices Adjusting the expression pedal (Calibration) If you find the expression pedal difficult to use, perform this procedure so that the pedal will function optimally. For example if the effect does not reach maximum when the pedal is advanced all the way, or does not reach minimum when the pedal is returned all the way, use the following procedure to make the appropriate adjustments. When making adjustments, use your hand to move the pedal. Accurate calibration may not be possible if you use your foot to operate the pedal. Turn on the power while simultaneously holding down the EXIT switch and the PEDAL switch. [. . . ] The pedal will control the reverb level. HALL (Hall Reverb) This simulates the reverberation of a mid-size to large hall. The pedal will control the reverb level. Advance the expression pedal all the way until the pedal indicator blinks, to enter record-ready mode. [. . . ]