User manual KORG KSERIES

[. . . ] 7 Making connections and turning on the power . 8 About the K-Series and the driver ports . 23 Owner’s Manual Precautions Location Using the unit in the following locations can result in a malfunction. € In direct sunlight • Locations of extreme temperature or humidity • Excessively dusty or dirty locations • Locations of excessive vibration • Close to magnetic fields • Reorient or relocate the receiving antenna. [. . . ] KNOB1 and KNOB2 By assigning MIDI control changes, these knobs can be used to operate external MIDI equipment and control musical software applications. The assignable values are “No Assign/Control Change”. 127] Turning the knob will change the value of the assigned parameter. 12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Owner’s Manual SW1 and SW2 These two switches can be assigned individually to send a specific value to a specific MIDI control change parameter. In fact, both an “on” and “off” value can be set. The switch type can be set to Momentary or Toggle. The assignable values on SW1 and SW2 are “No Assign/Program Change/Control Change”. no Assign No MIDI information is sent from this controller. Program Change Every time [SW1] is pressed, the program change number is decreased by 1. Every time [SW2] is pressed, the program change number is increased by 1. In addition, a program change message of “0” is sent if [SW1] are [SW2] are pressed simultaneously. In “Toggle” mode, each time a switch is pressed, a MIDI control message is sent; each press will alternate between the On Value and the Release Value. In “Momentary” mode, the On Value MIDI control message is sent when the switch is pressed down, and a Off Value MIDI control message is sent when the switch is released. — ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ OCTAVE SHIFT UP / OCTAVE SHIFT DOWN These buttons can shift pitch of the keyboard in one octave units. The octave shift range is different depending on the keyboard length. — ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 13 MOD wheel By assigning a MIDI control change number, the Modulation Wheel can be used to operate external MIDI equipment and control musical software applications. The assignable values are “No Assign/Control Change/After touch”. 127] Use the Mod Wheel to smoothly change the value of the assigned MIDI control change parameter. After Touch Use the Mod Wheel to send channel AFTERTOUCH messages. — ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ SLIDER By assigning a MIDI control change number, the Modulation Wheel can be used to operate external MIDI equipment and control musical software applications. The assignable values are “No Assign/Control Change”. 127] Use the slider to smoothly change the value of the assigned MIDI control change parameter. [. . . ]  No sound(K61P) • Make sure the K-Series’ volume is not set to “0”. please turn the volume to an appropriate position.  Notes are dropping out or being cut off before playing to completion • You may be exceeding the K61P’s polyphony limit. About Maximum Polyphony Maximum polyphony is the maximum number of notes that the internal sound engine is capable of producing at a single time. [. . . ]