User manual KORG N1

[. . . ] Content that is of particular importance is also printed in boldface type. Steps in a procedure are listed as 1 2 3 . . . p. s, BG p. s, s. s ­ s From the left, these symbols indicate a reference page in the Parameter Guide, a reference page in the Basic Guide, and a parameter number. Conventions in this manual Abbreviations for the manuals BG, PG, VNL References to the manuals included with the TRITON-Rack are abbreviated as follows. BG: Basic Guide PG: Parameter Guide VNL: Voice Name List Switches and knobs [ ] References to the keys, dials, and knobs on the TRITONRack's panel are enclosed in square brackets [ ]. References to buttons or tabs indicate objects in the LCD display screen. [. . . ] For details on the preset scales, refer to "Type" (PROG 2. 1­1c). 1 Select "Copy Scale" to access the dialog box. 114 2 Select the copy source scale ("From"). If you select Pure Major or Pure Minor, you must also specify the "Key" selection located at the right. Stretch can be selected only if "To" is the User All Notes Scale. 3 Select the copy destination scale ("To"). 4 To execute the Copy Scale command press the [F8] ("OK") key. To cancel without executing press the [F7] ("Cancel") key. GLOBAL 4. 1: Category Name 4. 1­1: P. 0. . 7 (Prog. 00­07) 4. 1­2: P. 8. . 15 (Prog. 08­15) 4. 1­3: C. 0. . 7 (Comb. 00­07) 4. 1­4: C. 8. . 15 (Comb. 08­15) Here you can assign names to the program and combination categories. Select the category whose name you wish to modify, press the [F5] ("TEXT") key to access the text dialog box, and input the name. A maximum of 16 characters can be input (BG p. 38). The category names you edit here can be selected in the dialog box when you write a program or combination. With the factory settings, these are classified by type of instrument. You can specify sixteen categories each for programs and combinations. Select the Utility "Write Drum Kits" to access the Write Drum Kits dialog box, or press the [WRITE] key to access the Update Drum Kits dialog box, and press the [F8] ("OK") key to write the edited settings. For details on creating a drum kit, refer to BG p. 78. 5. 1­1a: Drum Kit, Key, Assign, Level H, Level L , Vel. SW LH Drum Kit [000 (I­A/B). . . 143 (E­H)] Selects the drum kit that you wish to edit. If you wish to modify the drum kit name, use the "Rename Drum Kit" Utility menu command. 00(I­A/B) . . . 15(I­A/B) Preloard drum kits 16(E­A). . . 31(E­A) 32(E­B). . . 47(E­B) 48(E­C). . . 63(E­C) 64(E­D). . . 79(E­D) 80(E­E). . . 95(E­E) 96(E­F). . . 111(E­F) 112(E­G). . . 127(E­G) 128(E­H). . . 143(E­H) (for user drum kits and EXB-PCM series drum kits) Key [C­1. . . G9] Selects the key to which you will assign a drumsample (and its settings). To select the key, use the [F6] ("Key­"), [F7] ("Key+") keys. Alternatively if an external MIDI keyboard is connected via MIDI, you can hold down the [ENTER] key and play a note on the external MIDI keyboard. All 5. 1: DKit parameters except for "Drum Kit" will apply to the key you assign here. Two drumsamples, High and Low, can be assigned to each key, and you can switch between them by velocity as you play. Assign [Off, On] On (Checked): The drumsamples you assigned for High (5. 1­1b) and Low (5. 1­2a) will sound. Off (Unchecked): The selected drumsamples will be invalid, and the drumsamples of the key to the right will sound. At this time, the pitch will be a semitone lower than the pitch of the key to the right. Uncheck this parameter when you wish to play a drumsample at differing pitches. 5. 1­1: High (High Sample) Here you can select a drum kit, assign High and Low drumsamples to each key, and set parameters for the High and Low drumsamples. Level H (Level High) Level L (Level Low) [­99. . . +99] [­99. . . +99] Specify the volume of the High and Low drumsamples. Keys that are set to +99 will sound at a volume double that of the amp level of the program that uses this drum kit. [. . . ] 2 Use ADAT-OPTICAL cables to connect the respective IN and OUT connectors of the ADAT Optical format-compatible mixer and the ADAT. 3 Make connections as shown in the following diagram so that an Alesis BRC Remote Controller or other ADAT optical format compatible mixer or remote controller can be used as the master for digital signal synchronization, and connect the WORD CLOCK OUT connector of the mixer to the WORD CLOCK IN connector of the TRITON-Rack. For connections, use a BNC Coax cable made by Alesis Corporation or a BNC cable made for video (both sold separately). 4 Set the TRITON-Rack's "System Clock" to Word Clock. [. . . ]