User manual KORG NANOSERIES2

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. €¢ Increase the separation between the equipment and receiver. €¢ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] The Korg Kontrol Editor software allows you to edit MIDI messages transmitted via each controller on the nanoKEY2. You can download the Parameter Guide and the Korg Kontrol Editor software from the Korg website. Com When you first connect the nanoKEY2 to a computer running Windows XP/Vista/7, the standard USB-MIDI driver for your operating system will be installed automatically. MIDI OUT port This port is used by the Korg Kontrol Editor to control the nanoKEY2. If you are using Windows XP/Vista/7, the standard USBMIDI driver that is automatically installed will not allow you to use the nanoKEY2 with multiple applications simultaneously. If you want to use the nanoKEY2 with multiple applications simultaneously, you must install the Korg USB-MIDI driver. You can download the Korg USB-MIDI driver from the Korg website, and install it as described in the included documentation. Com Even if you don't need to use the nanoKEY2 with multiple applications simultaneously, we recommend that you install the Korg USB-MIDI driver for more stable operation. Mac OS X Computer: Apple Macintosh computer with an Intel or PowerPC processor that has a USB port Turning off the power 1. Disconnect the USB cable that’s connected to the nanoKEY2 and the computer. The power to the nanoKEY2 will turn off and the power LED will go dark. 4 or later nanoKEY2 operation is not guaranteed with all computers that satisfy these system requirements. NanoKEY2 and driver ports Driver ports As shown in the following table, the name of the ports will depend on which operating system you’re using, and whether or not you’ve installed the Korg USB-MIDI driver. OS Mac OS X Windows Vista/7 Windows XP Windows XP/Vista/7 + KORG USB-MIDI Driver MIDI IN nanoKEY2 KEYBOARD nanoKEY2 USB audio device nanoKEY2 1 KEYBOARD MIDI OUT nanoKEY2 CTRL nanoKEY2 USB audio device nanoKEY2 1 CTRL Specifications Connectors: Power supply: USB connector (mini B type) USB bus power mode Current consumption: 100 mA or less Dimensions (WxDxH): 12. 61 oz / 244 g USB cable, Owner’s manual Included items: Getting ready Connections and power Troubleshooting Power does not turn on •If you’re using a passive (non-powered) USB hub, the nanoKEY2 may fail to power-on because it’s not getting enough power. If this is so, please connect the nanoKEY2 to a powered USB hub or directly to your computer. * Specifications and appearance are subject to change without notice for improvement. MIDI IN port USB cable Computer USB connector nanoKEY2 This is where MIDI messages from the nanoKEY2’s various controllers are received. If you want to use the nanoKEY2 to control an application on your computer, then select this port in the MIDI input settings of your application. This is also used by the Korg Kontrol Editor to control the nanoKEY2. Software does not respond •Make sure that the nanoKEY2 has been detected by the connected computer. If you are using Windows XP, go to the Control Panel, open “Sounds, Speech, and Audio Devices” -> “Sounds and Audio Devices, ” and check the “Hardware” tab page to see if the nanoKEY2 is connected. [. . . ] The button LEDs indicate the keyboard’s octave shift status as follows. Octave shift status ±0 +1/-1 +2/-2 +3/-3 +4/-4 Octave LED color Unlit Green Orange Red Blinking red Keyboard does not respond to velocity •Check the velocity curve setting of the keyboard in the Korg Kontrol Editor software. Operating requirements Windows Keyboard There are twenty-five velocity-sensitive keys that transmit note messages. mOD button This button transmits modulation messages. [. . . ]