User manual KORG T SERIES BROCHURE

[. . . ] The DIRECT HD Styles are contained in three folders to the hard disk. These folders, automatically created by the T SERIES, have fixed names: Folder !123. SET !456. SET !789. SET DIRECT HD banks 1, 2, 3 4, 5, 6 7, 8, 9 WHAT'S A STYLE? A Style is a rhythm/accompaniment structure, that simulates a band backing your solos. In a vertical direction, it is composed of 8 different tracks (Drums, Percussions, Bass, and 5 different harmonic or melodic instruments). You can play on the keyboard with 4 more Realtime tracks (Upper 1-3 and Lower). [. . . ] Furthermore, it lets you activate/deactivate the alternative scale for each track. Use the TRACK SELECT button to switch between Song tracks 1-8, Song tracks 9-16, and back again. PAGE 8 - FX: A/B SELECT This page lets you select the A and B effects. Usually, the A effect is a reverb, while the B effect is a modulating effect. Standard MIDI Files usually exploit two effects only. You can, however, assign all four effects to a Song (see "Page 3 Mixer: FX Block" on page 12-5). Tuning:PB/Scale PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N FX:A/B Select A:02 BigHall ModTrk:Up1 B:97 MlwChrs B>Asend:127 Note: When you stop the Song, or select a different Song, the default effects are selected again. You can, however, stop the Song, change the effects, then start the Song again. Save the Song to permanently change the effects. Tuning:PB/Scale PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N PB:02 Sc:N A, B Effects assigned to the A and B effect processors. Usually, A is the reverb, while B is the modulating effect (chorus, flanger, delay. . . ). For a list of the available effects, see "Effects" on page 18-1. ModTrk (Modulating Track) PB(end) This parameters shows the Pitch Bend range for each track, in semitones. 01. . . 12 Maximum positive/negative pitchbend range (in semitones). Off No pitchbend allowed. Sc(ale) Source track for modulating MIDI messages. Use the VOLUME/VALUE (A-H) buttons to select a track. Use the F1-F4 buttons to select a sound parameter, or its value. (For the Drum and Percussion tracks, see below the "Drum tracks" section). Use the TEMPO/VALUE controls to change the sound parameter or its value. Parameters Attack PAGE 12 - FX: C EDITING This page contains the editing parameters for the C effect. For more details, see "Page 10 - FX: A editing" above. Decay Release Attack time. This is the time during which the sound goes from zero (at the moment when you strike a key) to it's maximum level. Time to go from the final Attack level to the beginning of the Release. This is the time during which the sound goes from the sustaining (or Song operating mode Page 15 - Track: Mode 12-9 Decay) phase, to zero. The Release is triggered by releasing a key. Resonance Use the Filter Resonance to define the width of the frequency range affected by the Filter. Vibrato Delay Delay time before the Vibrato begins, after the sound starts. PAGE 15 - TRACK: MODE This page lets you set the polyphony mode for each track. [. . . ] Note: Should you not do a back-up and your internal data is changed, you can download the data from www. korgpa80. com, or ask your local KORG dealer. Prepare 5 formatted, empty disks (1. 44MB, MS-DOS formatted). You can prepare this kind of disk using a PC or the T SERIES itself (see "Page 5 - Format" on page 15-14). Note: You can't prepare T SERIES Backup disks on a Macintosh. [. . . ]