User manual KORG TR

[. . . ] Operation Guide E 2 To ensure long, trouble-free operation, please read this manual carefully. Precautions Location Using the unit in the following locations can result in a malfunction. • In direct sunlight • Locations of extreme temperature or humidity • Excessively dusty or dirty locations • Locations of excessive vibration Power supply Please connect the designated AC/AC power supply to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended. Interference with other electrical devices This product contains a microcomputer. [. . . ] Set the pan and volume of each track (SEQ 1. 1: Play/REC, Mixer page) To turn off the Solo function, select the “SOLO On/Off” and press the [DEC] key once again. Select the track 1 and 2 “SOLO On/Off” and press the [DEC] key once each. The display will change, and the playback of tracks 1 and 2 will be muted. If the Solo function is turned off for all tracks, playback will be according to the “PLAY/MUTE/REC” settings. By using the Utility menu command “Solo Selected Track, ” you can listen to the sound of only the selected track. This is convenient when you want to set track parameters or to make effect settings. (☞PG p. 51) In the SEQ 1. 1: Play/REC, Mixer page, “Pan” sets the pan of each track, and “Volume” sets the volume of each track. 3. Specify the tone generator and MIDI channel that will sound each track (SEQ 3. 1: Param1, MIDI page) [LOCATE] settings By pressing the [LOCATE] key you can move to a specified location. The location is specified by the Utility menu command “Set Location. ” You can also hold down the [ENTER] key and press the [LOCATE] key to set the location even during playback (☞PG p. 54). Normally you will set this to 001:01. 000. You will return to the beginning of the song. When you select a song, the [LOCATE] setting will automatically be set to 001:01. 000. In the SEQ 3. 1: Param1, MIDI page, “Status” specifies whether each track will sound the internal tone generator or an external tone generator. “MIDI Channel” specifies the MIDI channel for each track. If the track status “Status” is set to INT, playing the track data or operating the TR’s keyboard or controllers will cause the TR’s internal tone generator to be sounded and controlled. If “Status” is set to EXT, EX2, or BTH, playing the track data or operating the TR’s keyboard or controllers will cause an external tone generator to be sounded and controlled. (The MIDI channel of the external tone generator must be set to match the “MIDI Channel” of TR tracks that are set to EXT, EX2 or BTH. ) If “Status” is set to BTH, both the external tone generator and the TR’s own tone generator will be sounded and controlled. If you are using the TR’s Sequencer mode as a 16track multi-timbral tone generator, set this parameter to INT or BTH. (☞”Status” PG p. 62) In general, you should set “MIDI Channel” to different channels 1–16 for each track. Tracks that are sent to the same MIDI channel will sound simultaneously when either is recorded or played. Making track settings for a new song Here’s how to make basic settings for a new song, such as assigning a program to each track, and setting the volume etc. You can check these settings for the template song you loaded earlier. 1. Assign a program to each track (SEQ 1. 1: Play/REC, Program page) 4. Make effect settings (SEQ 7. 1: Insert FX, SEQ 7. 2: Master FX) Make settings for each effect in SEQ 7. 1: Insert FX and SEQ 7. 2: Master FX. [. . . ] 16 Selecting mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Selecting parameter. . . . . . . . . . . . . . . . . . . . . . 16 Send AUDIO INPUT. . . . . . . . . . . . . . . . . . . . . . . 114 Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]