User manual KRESS 1050 FME-1

[. . . ] English 15 Work area safety Keep work area clean and well lit. cluttered and dark areas invite to accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite dust or fumes. [. . . ] English 17 To mark the machine, do not drill into the housing. Never use the machine with a damaged cable. Do not touch the damaged cable and pull the mains plug when the cable gets damaged during operation. Although this information sheet and the operating manuals for our electrical tools contain extensive instructions on safe working with electrical tools, every electrical tool involves certain residual risks that cannot be completely prevented through safety mechanisms. Therefore, electrical tools must always be operated with the necessary caution. Mm 40 Milling-ø mm 30 Dimension mm 240x73 Weight kg 1, 3 Protection class II Milling and grinding motor 800FME Input power Watt 800 Output power Watt 420 Idle speed min-1 10. 000 Speed for rated load min-1 Tool fitting with collet chuck ø mm 8 Grinding tool ø, max. Mm 40 Milling-ø mm 36 Dimension mm 262x73 Weight kg 1, 4 Protection class II Milling and grinding motor 1050FME Input power Watt 1050 Output power Watt 600 Idle speed: 1050FME min-1 10. 800 Speed for rated load min-1 Tool fitting with collet chuck ø mm 8 Grinding tool ø, max. Mm 40 Milling-ø mm 36 Dimension mm 289x73 Weight kg 1, 7 Protection class II Your power tool is doubly insulated in compliance with EN 60745; there is thus no need for an earth wire. The machine is radio and TV interference-free in accordance with EN 55014-1 and interferenceproof in accordance with EN 55014-2. Read all the warnings and instructions before using the equipment. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. While reading the operating instructions, unfold the graphics page for the machine and leave it open. Device components 1 2 3 4 5 6 7 8 Locknut Collet chuck Spindle Locking button On/off switch Speed governor turning wheel Mains cable module Locking for mains cable module Illustrated or described accessories are not necessarily included in the scope of delivery Scope of supply See packaging The fitted milling and grinding motor is designed for milling wood and plastics and for grinding wood, plastic, steel and aluminium. The motor must not be guided by hand without appropriate milling attachments. The personnel must be made aware of the relevant dangers. Milling and grinding motor Input power Watt Output power Watt Idle speed min-1 Speed for rated load min-1 Noise levels Measurement values determined according to EN 60 745. Operation The A-weighted noise level of the device is typically: 78 dB(A) Sound pressure level (LpA) Sound power level (LwA) 89 dB(A) Measurement uncertainty K = 3 dB The noise level can exceed 85 dB(A) during operation. Vibration Triaxial vibration emission level determined in accordance with EN 60745. Milling ah m/s² 5, 0 Measurement uncertainty K m/s² 1, 5 The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet. [. . . ] Replacing brushes Worn carbon brushes should be replaced by an authorised customer service organisation. This power tool has been carefully tested and has been subjected to a strict quality control process. We guarantee the free-of-charge repair of faults in the power tool that arise within 24 months from the date of purchase at the end user's premises and which can be attributed to a material or manufacturing defect. Inappropriate use or handling and opening up the device by unauthorised repair centres leads to the warranty becoming void. [. . . ]