User manual KRESS 144 AFB 1.5 SET

[. . . ] The term "power tool" in all of the warnings listed below refers to your mains operated (corded) power tool. 1) WORK AREA a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. [. . . ] Power tools are dangerous in the hands of untrained users. 7 e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR HAMMER DRILLS Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Wear ear protectors with hammer drills (exposure to noise can cause hearing loss) Use auxiliary handles supplied with the tool (loss of control can cause personal injury) Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (UK 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug KRESS can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Be careful not to drill or drive into areas where electrical wires may be contacted If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool Be aware of the forces that occur as a result of jamming (especially when drilling metals); always hold the tool firmly with both hands and take a secure stance On/Off 5 Switch locking for continuous use 6 Speed control for smooth starting 7 Maximum speed control With wheel C the maximum speed can be adjusted from low to high (1-5) - switch on the tool - lock the switch - turn wheel C to select maximum speed For determining speed, table ^ can be used as reference Changing direction of rotation 8 - when not properly set in left/right position, switch A cannot be activated !Un cble endommag ou torsad augmente le risque d'un choc lectrique. e) Au cas o vous utiliseriez l'outil lectroportatif l'extrieur, utilisez une rallonge autorise homologue pour les applications extrieures. L'utilisation d'une rallonge lectrique homologue pour les applications extrieures rduit le risque d'un choc lectrique. 3) SECURITE DES PERSONNES a) Restez vigilant, surveillez ce que vous faites. Faites preuve de bon en utilisant l'outil lectroportatif. N'utilisez pas l'appareil lorsque vous tes fatigu ou aprs avoir consomm de l'alcool, des drogues ou avoir pris des mdicaments. Un moment d'inattention lors de l'utilisation de l'appareil peut entraner de graves blessures sur les personnes. Always keep tool and cord clean (especially the ventilation slots) !GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 100 dB(A) en het geluidsvermogen-niveau 111 dB(A) (standaard deviatie: 3 dB), en de vibratie 11, 7 m/s2 (hand-arm methode). CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. bestmmelser och riktlinjema 73/23/EG, 89/336/EG, 98/37/EG. LJUD/VIBRATION Ljudtrycksnivn som uppmtts enligt EN 60 745 r p denna maskin 100 dB(A) och ljudeffektnivn 111 dB(A) (standard deviation: 3 dB), och vibration 11, 7 m/s2 (hand-arm metod). [. . . ] CE STANDARDIZASYON BEYANI Yeane sorumlu olarak, bu rnn aflaidaki standartlara veya standart belgelerine uygun olduunu beyan ederiz: EN 60 745, EN 55 014, ynetmelii hkmleri uyarinca 73/23/EC, 89/336/EC, 98/37/EC. / GRLT/T<TREfiIM llen EN 60 745 gre ses basinci bu makinanin seviyesi 100 dB(A) ve al>flma s>ras>ndaki grlt 111 dB(A) (standart sapma: 3 dB), ve titreflim 11, 7 m/s2 (el-kol metodu). F D NL S DK N FIN E P I H CZ TR 05 KRESS Europe B. V. Kloot 74 PL OWIADCZENIE ZGODNOCI CE Niniejszym owiadczamy ponoszc osobist odpowiedzialno, e produkt wykonany jest zgodnie z nastpujcymi normami i dokumentami normalizujcymi: EN 60 745, EN 55 014, z godnie z wytycznymi 73/23/WE, 89/336/WE, 98/37/WE. HAASU/WIBRACJE Pomiarw dokonano zgodnie z norm EN 60 745 cinienie akustyczne narzdzia wynosi 100 dB(A) za poziom mocy akustycznej 111 dB(A) (poziom odchylenie: 3 dB), za wibracje 11, 7 m/s2 (metoda do-rka). [. . . ]