User manual KRUPS NOVO 3000 FNC2

[. . . ] www. krups. com a b d f g h e j k k1 i k3 l m d k2 o p n q 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 A B C 36 37 38 8 Novo 3000 Novo 3000 Premium FNC2 FNC3 USA Instructions for Use Warranty Guarantee of Performance 8 Français Mode d'emploi Garantie Garantie de rendement 19 Español Instrucciones de uso Garantía Garantía de rendimiento 30 7 USA IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: ·Read all instructions. ·To protect against fire, electric shock and injury to persons, do not immerse cord, plugs, or appliance in water or other liquid. ·Close supervision is necessary when any appliance is used by or near children. ·Unplug from outlet when not in use and before cleaning. [. . . ] Once the appliance reaches the correct temperature, the orange temperature control light will go out. · Then turn the selector to the Tear excess paper from pod at perforated edge. Place the ESE pod with the RED MARKING FACE DOWN (bend the paper corners down). LOCKING the handle TIGHTLY and PROPERLY will avoid leakage from the filter holder and ensure a better brewing cycle. Place the filter holder inside the brewing head and FIRMLY turn the handle as far RIGHT as possible. Once the appliance reaches the correct temperature, the orange temperature control light will go out. · Then turn the selector to the setting (10). · When the recommended quantity of coffee has been reached (about two ounce) turn the selector to the O position. Remove the ESE filter holder from the brewing head and throw away the used coffee pod. NOTE: Other pods (such as those sold by Starbucks ) can be used in your Krups Novo 3000 & 3000 Premium as long as they are E. S. E. standard pods. illy is a registered trademark of illy espresso of the americas, inc. Starbucks is a registered trademark of the Starbucks Coffee Company. 2. STEAM FUNCTION FOR PREPARING CAPPUCCINO AND LATTE setting (10). · When the cup is full of hot water, reset the selector to the O setting. Once the machine has heated up, the espresso cups can be pre-heated on the cup warming plate (on top of the machine). Preparing an espresso: Place the serving of "illy in the ESE filter holder fitted with its own filter. The wording "illy must be pointing towards the bottom. Setting the ESE pod Placing the ESE pod correctly will create a richer, thicker crema. The thumping noise which occurs while steam is being produced comes from the intermittent regulation of the pump and has no effect on the proper working of the appliance. If you wish to make an espresso immediately after using the steam function, the appliance must first be allowed to cool down in order to achieve the correct temperature for preparing an espresso. Keep the container straight during this operation. Do not allow the tip of the nozzle to touch the bottom of the container because this could obstruct the steam output. · Once you have obtained the desired quantity of frothy milk, turn the selector to the O setting. · After use, remove the flexible tube from the container and clean the auto cappuccino accessory (see section "Cleaning the Machine"). · Turn the selector to the . Preparing hot, steamed milk for a cafe latte, hot chocolate or for heating water (for tea, for example). Hot chocolate: immerse the flexible tube directly into the carton if the chocolate milk is ready-made, or heat the milk if you are using powdered chocolate. [. . . ] Clean the filter and the grid on the head. See the paragraph «Maintenance» and try a coarser coffee. Put the grid to soak in descaling solution See paragraph «Maintenance». See paragraph «Descaling». Recipes Savor your espresso just as you like it: when you want to relax or to top off a good meal. [. . . ]